Enterasys Networks CM Version 1.0 manual Unpacking the DC Power Supply

Page 27

Unpacking the DC Power Supply

Warning: To reduce the risk of electric shock or energy hazards: 1. Connect to a reliably grounded 48V source.

2.The branch circuit over current protection must be rated at a maximum 50A for the device.

3.Use only 10mm² or 6 AWG 75C solid copper wires on the device.

4.A readily accessible disconnect device that is suitably approved and rated shall be incorporated in the field wiring.

5.To be installed in a restricted access area in accordance with the NEC or authority having jurisdiction.

Advertencia: Para reducir el riesgo de choque electrico:

1.Conectar a una fuente aterrizada de 48V.

2.The branch circuit over current protection must be rated at a maximum 50A for the device.

3.Utilizar unicamente cables de cobre solidos de tipo 75C 10mm² or 6 AWG en el dispositivo.

4.A readily accessible disconnect device that is suitably approved and rated shall be incorporated in the field wiring.

5.Ser instalado en una area de acceso restrictivo, de acuerdo con el NEC o con otra autoridad.

Warnhinweis: Reduzieren sie das Risiko von Stromschlägen oder allgemeinen elektrischen Gefahren:

1.Verbinden Sie das Gerät mit einer zuverlässig geerdeten 48 V Stromquelle.

2.Die maximale Absicherung des Stromkreises für dieses Gerät beträgt 50A.

3.Benutzen Sie zum Anschluß des Gerätes ausschließlich Kabel mit soliden Kupferadern des Querschnitts 10mm² (6 AWG) 75C.

4.Das Stromnetz am Installationsort sollte mit einem frei zugänglichen Spannungs- Unterbrecher (Not-Aus-Schalter) ausgestattet sein, der ausreichend ausgelegt ist und den gängigen Bestimmungen entspricht.

5.Die Installation sollte in zugangskontrollierten Räumen erfolgen, entsprechend den Vorschriften der NEC bzw. der örtlich zuständigen Behörden.

Unpacking the DC Power Supply

To unpack the DC power supply:

1.Open the box and remove the packing material protecting the DC power supply.

2.Verify the contents of the carton as listed in Table 1‐4.

Matrix X Router DC Power Supply Installation Guide 1-9

Image 27
Contents Enterasys Matrix X Router Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys Networks, Inc. Firmware License Agreement Viii Page Page Contents Xii For information about Refer to Using This GuideUsing the Enterasys Matrix X Router Manual Set Who Should Use This GuideFollowing conventions are used in this guide Conventions Used in This GuideSupport@enterasys.com Getting HelpGetting Help Xvi About This Guide DC Power Supply Installation Overview of the DC Power Supply Circuit breakerEarth ground stud Back View of the DC Power Supply Power Supply Redundancy Planning Installation Site RequirementsVerify DC Power Compliance of Matrix X Modules Pre-Installation TasksWorksheet DC Compliance of Modules in Existing AC Systems Model Part No Part NumberDC Compliant? Model Part No Front Panel Serial Number DC Compliant? Worksheet DC Compliance of Modules for New DC SystemsModel Name Minimum 940 Part Number Minimum 940 Revision Minimum Revision of X Modules for DC PowerUnpacking the DC Power Supply Contents of X-DC Carton Installing the DC Power SupplyRemoving Power Supply Vent Plate Installing Power Supply Module Power supply slot Power supply coverplate Removing Blank Coverplate from Power Supply SlotRemoving a Power Supply Removing a Power Supply Removing a Power Supply DC Power Supply Installation Specification SpecificationsPhysical Specifications Electrical SpecificationsCompression Lugs Power Supply RedundancyModule Module Power SpecificationsRedundancy Configurations for DC Power Supply @ 48 VDCRegulatory Compliance Compliance StandardsRegulatory Compliance Standards