Enterasys Networks 3000 manual Interference Statement

Page 5

Ein Artikel, der mit CExxxx oder dem CE‐Warnhinweis gekennzeichnet ist, enthält einen Funksender, der den Anforderungen der R&TTE‐Richtlinie (1999/5/EC) der EU‐Kommission entspricht. Die Übereinstimmung mit dieser Richtlinie schließt die Konformität mit den folgenden europäischen Normen ein (die entsprechenden internationalen Normen sind in Klammern angegeben).

EN 300 328‐1 December 2001 V1.3.1

EN 300 328‐2 December 2001 V1.2.1

EN 301 893 August 2003 V1.2.3

EN 301 489‐1 August 2002 V1.2.1

EN 301 489‐17 August 2000 V1.2.1

EN 60950 (IEC60950) January 2000

Den Typ des Senders entnehmen Sie dem Kennzeichnungsetikett Ihres drahtlosen LAN‐Geräts.

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

If the RBT3K‐AG or RBT3K‐AG‐G device is going to be operated in 5.15 ~ 5.25GHz frequency range, then it is restricted in indoor environment only.

This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.

Enterasys Networks declares that the RBT3K‐1G, RBT3K‐AG, and RBT3K‐AG‐G (RoamAbout Access Point 3000) are limited in the 2.4 GHz band on channel 1‐11 by specified firmware controlled in USA.

Canada - Industry Canada (IC)

This Class B digital apparatus complies with Canadian ICES‐003.

Cet appareil numérique de la classe B est conforme à la norme NMB‐003 du Canada.

iii

Image 5
Contents RoamAbout Page Page Europe European Union Notice Interference Statement FIN Approved Countries RBT3K-AG5150 5350-MHz 12400 -2483.5 MHz RBT3K-AG5150 5350 MHz 12400 2483.5 MHz Portugal Enterasys Networks, Inc Firmware License Agreement Page Page Xii Contents Figures Purpose of This Manual About This GuideIntended Audience Associated DocumentsWorld Wide Web Phone Getting HelpOverview Kit ChecklistIntroduction Hardware Description ‐1 displays the top view and back panel of the Access PointAntennas LED IndicatorsComponent Description Security Slot Reset ButtonConsole Port Ethernet PortApplications Features and BenefitsPower Connector Applications Introduction Preparing to Install Hardware InstallationMounting the Access Point Mounting on a Horizontal SurfaceMounting on a Wall Mounting the Access Point Mounting on the Ceiling Removing the Access Point from the Mounting Bracket Connecting the Cables Lock Console POE Connecting the Cables Hardware Installation Required Connections Initial ConfigurationUsing the CLI Initial Configuration Using the CLI Disable DHCP. Type no ip dhcp Using the CLI Using Web Management Using Web Management Using Web Management Using Web Management Click the Management Vlan Enable radio button Login General Specifications SpecificationsPower Supply Network ConfigurationWeight Modulation TypeRadio Signal Certification TemperatureNetwork Management HumidityStandards Safety802.11a Sensitivity802.11g 802.11bTransmit Power Feature Parameter Default Default SettingsVlan WEP Feature Parameter Default Twisted-Pair Cable Assignments Cables and Pin-outs10/100BASE-TX Pin Assignments Straight-Through WiringConsole Port Pin Assignments Crossover WiringRTS request to send CTS clear to send Unused Troubleshooting Steps TroubleshootingTroubleshooting Steps Maximum Distance Tables Maximum Distance Tables Troubleshooting