Enterasys Networks 3000 manual Cables and Pin-outs, Twisted-Pair Cable Assignments

Page 53

C

Cables and Pin-outs

Twisted-Pair Cable Assignments

Caution: DO NOT plug a phone jack connector into the RJ-45 port. Use only twisted-pair cables with RJ-45 connectors that conform with FCC standards.

Precaución: NO utilice un conector de teléfono en el puerto RJ-45. Utilice solamente cable de par trenzado con conectores RJ-45 para cumplir con los estándares de la FCC.

Achtung: Verbinden Sie keine Telefonkabel mit dem RJ-45-Anschluss. Verwenden Sie ausschließlich verdrillte Kabel mit RJ-45-Anschlüssen, die den FCC-Standards entsprechen.

For 10/100BASE‐TX connections, a twisted‐pair cable must have two pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. Also, an RJ‐45 connector must be attached to both ends of the cable.

Caution: Each wire pair must be attached to the RJ-45 connectors in a specific orientation. (Refer to “Straight-Through Wiring” on page C-2and “Crossover Wiring” on page C-3for an explanation.)

Precaución: Cada par debe estar adjunto a los contactos del conector RJ-45 en una orientación específica. Refiérase a “Straight-Through Wiring” y “Crossover Wiring” para una explicación al respecto.

Achtung: Jedes Kabelpaar muss in einer bestimmten Ausrichtung mit den RJ-45-Anschlüssen verbunden werden. Weitere Informationen hierzu finden Sie unter „Straight-Through Wiring“ (Standard-Verkabelung) und „Crossover Wiring“ (Crossover-Verkabelung).

Figure C‐1 illustrates how the pins on the RJ‐45 connector are numbered. Be sure to hold the connectors in the same orientation when attaching the wires to the pins.

Figure C-1 RJ-45 Connector Pin-Out

8

8

11

RoamAbout Access Point 3000 Hardware Installation Guide C-1

Page 52 Page 54
Image 53
Page 52 Page 54
Contents RoamAbout Page Page Europe European Union Notice Interference Statement FIN Approved Countries RBT3K-AG5150 5350-MHz 12400 -2483.5 MHz RBT3K-AG5150 5350 MHz 12400 2483.5 MHz Portugal Enterasys Networks, Inc Firmware License Agreement Page Page Xii Contents Figures Purpose of This Manual About This GuideIntended Audience Associated DocumentsWorld Wide Web Phone Getting HelpOverview Kit ChecklistIntroduction Hardware Description ‐1 displays the top view and back panel of the Access PointAntennas LED IndicatorsComponent Description Security Slot Reset ButtonConsole Port Ethernet PortApplications Features and BenefitsPower Connector Applications Introduction Preparing to Install Hardware InstallationMounting the Access Point Mounting on a Horizontal SurfaceMounting on a Wall Mounting the Access Point Mounting on the Ceiling Removing the Access Point from the Mounting Bracket Connecting the Cables Lock Console POE Connecting the Cables Hardware Installation Required Connections Initial ConfigurationUsing the CLI Initial Configuration Using the CLI Disable DHCP. Type no ip dhcp Using the CLI Using Web Management Using Web Management Using Web Management Using Web Management Click the Management Vlan Enable radio button Login General Specifications SpecificationsPower Supply Network ConfigurationWeight Modulation TypeRadio Signal Certification TemperatureNetwork Management HumidityStandards Safety802.11a Sensitivity802.11g 802.11bTransmit Power Feature Parameter Default Default SettingsVlan WEP Feature Parameter Default Twisted-Pair Cable Assignments Cables and Pin-outs10/100BASE-TX Pin Assignments Straight-Through WiringConsole Port Pin Assignments Crossover WiringRTS request to send CTS clear to send Unused Troubleshooting Steps TroubleshootingTroubleshooting Steps Maximum Distance Tables Maximum Distance Tables Troubleshooting
Top Page Image Contents