Enterasys Networks 4H4285-49, 6H308-48, 9033989-06 manual Contents

Page 13

	Contents
About This Guide
Who Should Use This Guide	xv
How to Use This Guide	xvi
Related Documents	xvi
Conventions Used in This Guide	xvii
Getting Help	xviii
Chapter 1: Introduction
Overview of DFE-Gold PoE Module Capabilities	1-2
DFE-Gold Module	1-2
Connectivity	1-5
Management	1-5
Switch Configuration Using WebView	1-5
Switch Configuration Using CLI Commands	1-5
Secure Networks Policy Support	1-5
Standards Compatibility	1-6
LANVIEW Diagnostic LEDs	1-6
Chapter 2: Network Requirements
Link Aggregation	2-1
10BASE-T Network	2-2
100BASE-TX Network	2-2
Chapter 3: Installation
Installation Site Requirement	3-2
Unpacking the DFE Module	3-2
Installing Optional Network Expansion Module (NEM)	3-3
DFE Module Placement and Installation Rules	3-3
Preparing to Install the 4H4285-49	3-6
Installing 4H4285-49 into a Matrix E7 or N7 Chassis	3-7
Installing 4H4285-49 into Matrix N3 or N5 Chassis	3-10
Connecting 48 Vdc Power for PoE Operation	3-12
Connecting to the Network	3-13
Connecting UTP Cables to 4H4285-49	3-13
Connecting to COM Port for Local Management	3-18
What Is Needed	3-18
Connecting to an IBM PC or Compatible Device	3-18
Connecting to a VT Series Terminal	3-19
Connecting to a Modem	3-21
Adapter Wiring and Signal Assignments	3-23

xi

Image 13

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix a Specifications TroubleshootingAppendix B Mode Switch Settings and Option Installations Appendix C About PoE Power over EthernetTables FiguresXiv Who Should Use This Guide About This GuideImportant Notice Related Documents How to Use This GuideFor Refer to Following conventions are used in this guide Conventions Used in This GuideGetting Help For information about Refer to IntroductionDFE-Gold Module Overview of DFE-Gold PoE Module Capabilities4H4285-49 DFE-Gold Module 4H4285-49 DFE-Gold Module Switch Configuration Using CLI Commands Switch Configuration Using WebViewConnectivity ManagementStandards Compatibility Lanview Diagnostic LEDsLink Aggregation Network Requirements100BASE-TX Network 10BASE-T NetworkInstallation Contents of DFE Module Carton Quantity Installation Site RequirementUnpacking the DFE Module DFE Module Placement and Installation Rules Installing Optional Network Expansion Module NEMExample 1 -1, a Example 3 -1, C Preparing to Install the 4H4285-49 Installing 4H4285-49 into a Matrix E7 or N7 Chassis Preparing to Install the 4H4285-49 Card guides Installing 4H4285-49 into Matrix N3 or N5 Chassis Card guides Connecting 48 Vdc Power for PoE Operation Connecting UTP Cables to 4H4285-49 Connecting to the NetworkMaking the UTP Connections Connecting a Twisted Pair Segment with RJ45 Connector RX+ TX+ RX+ Verifying PoE Port Status What Is Needed Connecting to COM Port for Local ManagementConnecting to an IBM PC or Compatible Device Parameter Setting Connecting to a VT Series Terminal10 Connecting a VT Series Terminal Connecting to a Modem 11 Connecting Using a Modem COM Port Adapter Wiring and Signal Diagram RJ45 Adapter Wiring and Signal AssignmentsVT Series Port Adapter Wiring and Signal Diagram RJ45 DB25Completing the Installation of a New System Completing the InstallationModem Port Adapter Wiring and Signal Diagram RJ45 DB25 First-Time Log-In Using a Console Port Connection 12 Matrix Defogged Startup Screen Example N7 Chassis Enter Logging in with an Administratively-Configured User AccountCompleting the Installation Using Lanview TroubleshootingAbout the Management Mgmt LED Lanview LEDs Viewing Receive/Transmit ActivityColor State Recommended Action Viewing the PoE Port StatusAlternately 67% on, 33% LED RX/TX Refer to the Matrix DFE-Gold Series Configuration Troubleshooting ChecklistMatrix DFE-Gold Series Configuration Guide for OFFLINE/RESET Switch Overview of DFE Module Shutdown ProcedureLast Resort Shutdown Procedure Using OFFLINE/RESET Switch Recommended Shutdown Procedure Using OFFLINE/RESET Switch4H4285-49 Specifications SpecificationsTable A-1 4H4285-49 Specifications Processors/Memory Table A-1 4H4285-49 Specifications ItemSpecificationCOM Port Pinout Assignments Table A-2 COM Port Pin Assignments Signal Name Input/OutputRegulatory Compliance Table A-3 Compliance Standards Regulatory ComplianceRegulatory Compliance Specifications Required Tools Mode Switch Settings and Option InstallationsSetting the Mode Switches Memory Locations and Replacement Procedures Memory Locations and Replacement ProceduresGaining Access to Memory Modules Gaining Access to Memory ModulesRemoving the Safety Cover Figure B-3 Removing the Safety Cover Removing the Network Expansion Module NEM Dram Simm Replacement ProcedureFigure B-5 Removing the Existing Dram Simm Removing the Dram SimmFigure B-6 Installing the Dram Simm Installing the Dram SimmRemoving the Dimm Dimm Replacement ProcedureFigure B-8 Installing the Dimm Installing the DimmFigure B-9 Installing the Network Expansion Module Reinstalling the Optional Network Expansion ModuleReinstalling the Safety Cover Figure B-10 Installing the Safety Cover Overview About PoE Power over EthernetProprietary PD Detection Power InterfaceMatrix N5 Backplane 48 Vdc Interface Front Panel 48 Vdc InterfaceTable C-2 PoE Status LED Indications PoE Port Status PoE Port Status LEDsPoE Port Status LEDs About PoE Power over Ethernet Numerics IndexPinout assignments console port A-3

Related manuals

Manual 56 pages 18.08 Kb