Enterasys Networks 6H308-48, 9033989-06 manual Preparing to Install the 4H4285-49

Page 36

Preparing to Install the 4H4285-49

3.Slide the module into the slot until you can engage the top and bottom locking levers with the chassis as shown in Figure 3‐2.

Caution: In step 4, do not force the locking levers to the point that they touch the face of the front panel. Forcing the locking levers to this point could damage the module and chassis.

Precaución: En el paso 4, tenga cuidado de no llevar las palancas de cierre a un punto en donde estén en contacto con el panel frontal. Si lo hace, podría dañar el módulo o el chasis.

4.Refer to the Caution note above, then rotate the two levers into the closed position.

5.If the chassis in which the module is installed was powered down for the installation, turn the power supplies on. Check to see that the module CPU LED settles at solid green after a few minutes. If the LED does not turn solid green, refer to Chapter 4 for troubleshooting details.

3-8 Installation

Image 36

Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Troubleshooting Appendix a SpecificationsAppendix B Mode Switch Settings and Option Installations Appendix C About PoE Power over EthernetFigures TablesXiv About This Guide Who Should Use This GuideImportant Notice How to Use This Guide Related DocumentsFor Refer to Conventions Used in This Guide Following conventions are used in this guideGetting Help Introduction For information about Refer toOverview of DFE-Gold PoE Module Capabilities DFE-Gold Module4H4285-49 DFE-Gold Module 4H4285-49 DFE-Gold Module Switch Configuration Using WebView Switch Configuration Using CLI CommandsConnectivity ManagementLanview Diagnostic LEDs Standards CompatibilityNetwork Requirements Link Aggregation10BASE-T Network 100BASE-TX NetworkInstallation Installation Site Requirement Contents of DFE Module Carton QuantityUnpacking the DFE Module Installing Optional Network Expansion Module NEM DFE Module Placement and Installation RulesExample 1 -1, a Example 3 -1, C Preparing to Install the 4H4285-49 Installing 4H4285-49 into a Matrix E7 or N7 Chassis Preparing to Install the 4H4285-49 Card guides Installing 4H4285-49 into Matrix N3 or N5 Chassis Card guides Connecting 48 Vdc Power for PoE Operation Connecting to the Network Connecting UTP Cables to 4H4285-49Making the UTP Connections Connecting a Twisted Pair Segment with RJ45 Connector RX+ TX+ RX+ Verifying PoE Port Status Connecting to COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Connecting to a VT Series Terminal Parameter Setting10 Connecting a VT Series Terminal Connecting to a Modem 11 Connecting Using a Modem Adapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45VT Series Port Adapter Wiring and Signal Diagram RJ45 DB25Completing the Installation Completing the Installation of a New SystemModem Port Adapter Wiring and Signal Diagram RJ45 DB25 First-Time Log-In Using a Console Port Connection 12 Matrix Defogged Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User Account EnterCompleting the Installation Troubleshooting Using LanviewAbout the Management Mgmt LED Viewing Receive/Transmit Activity Lanview LEDsViewing the PoE Port Status Color State Recommended ActionAlternately 67% on, 33% LED RX/TX Troubleshooting Checklist Refer to the Matrix DFE-Gold Series ConfigurationMatrix DFE-Gold Series Configuration Guide for Overview of DFE Module Shutdown Procedure OFFLINE/RESET SwitchRecommended Shutdown Procedure Using OFFLINE/RESET Switch Last Resort Shutdown Procedure Using OFFLINE/RESET SwitchSpecifications 4H4285-49 SpecificationsTable A-1 4H4285-49 Specifications Table A-1 4H4285-49 Specifications ItemSpecification Processors/MemoryTable A-2 COM Port Pin Assignments Signal Name Input/Output COM Port Pinout AssignmentsRegulatory Compliance Table A-3 Compliance Standards Regulatory ComplianceRegulatory Compliance Specifications Mode Switch Settings and Option Installations Required ToolsSetting the Mode Switches Memory Locations and Replacement Procedures Memory Locations and Replacement ProceduresGaining Access to Memory Modules Gaining Access to Memory ModulesRemoving the Safety Cover Figure B-3 Removing the Safety Cover Dram Simm Replacement Procedure Removing the Network Expansion Module NEMRemoving the Dram Simm Figure B-5 Removing the Existing Dram SimmInstalling the Dram Simm Figure B-6 Installing the Dram SimmDimm Replacement Procedure Removing the DimmInstalling the Dimm Figure B-8 Installing the DimmReinstalling the Optional Network Expansion Module Figure B-9 Installing the Network Expansion ModuleReinstalling the Safety Cover Figure B-10 Installing the Safety Cover About PoE Power over Ethernet OverviewPower Interface Proprietary PD DetectionMatrix N5 Backplane 48 Vdc Interface Front Panel 48 Vdc InterfacePoE Port Status LEDs Table C-2 PoE Status LED Indications PoE Port StatusPoE Port Status LEDs About PoE Power over Ethernet Index NumericsPinout assignments console port A-3

Related manuals

Manual 56 pages 18.08 Kb