Enterasys Networks 6H308-48, 4H4285-49, 9033989-06 manual Troubleshooting Checklist

Page 63

Troubleshooting Checklist

Troubleshooting Checklist

If the module is not working properly, refer to Table 4‐2 for a checklist of problems, possible causes, and recommended actions to resolve the problem.

Table 4-2 Troubleshooting Checklist

Problem

Possible Cause

Recommended Action

 

 

 

All LEDs are OFF.

Loss of power.

Ensure that the module was installed properly

 

 

according to the installation instructions in

 

 

Chapter 3, and that the host chassis is providing

 

 

power.

 

 

 

No Local

Incorrect terminal setup.

Refer to the Matrix DFE-Gold Series Configuration

Management

 

Guide for proper setup procedures.

Password screen.

 

 

Improper console cable

Refer to Appendix A for proper COM port pinouts.

 

 

pinouts.

 

 

 

 

 

Corrupt firmware image,

If possible, attempt to download the image to the

 

or hardware fault.

module again. Refer to “Setting the Mode

 

 

Switches” on page B-2 for instructions to clear

 

 

NVRAM.

 

 

 

Cannot navigate

Improper username/

If the username/password combination has been

beyond Password

password combination

forgotten, refer to Refer to “Setting the Mode

screen.

entered.

Switches” on page B-2 for instructions on how to

 

 

set the mode switch to reset the username/

 

 

password combination to the default values.

Cannot contact the module through in-band management.

IP address not

Refer to the Matrix DFE-Gold Series Configuration

assigned.

Guide for the IP address assignment procedure.

 

 

Port is disabled.

Enable port. Refer to the Matrix DFE-Gold Series

 

Configuration Guide for instructions to enable/

 

disable ports.

 

 

Host Port policy and/or

Verify that a management VLAN exists and that it

management VLAN is

is associated with the Host Port.

incorrectly configured,

Refer to the Matrix DFE-Gold Series Configuration

or not configured.

Guide for information about Host Port and

 

 

management VLAN configuration.

 

 

No link to device.

Verify that all network connections between the

 

network management station and the module are

 

valid and operating.

 

If the problem continues, contact Enterasys

 

Networks for technical support.

Matrix DFE-Gold Series PoE Module 4H4285-49 Installation Guide 4-7

Image 63
Contents Enterasys Matrix Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Safety Information Class 1 Laser Transceivers Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Appendix C About PoE Power over Ethernet TroubleshootingAppendix a Specifications Appendix B Mode Switch Settings and Option InstallationsTables FiguresXiv About This Guide Who Should Use This GuideImportant Notice How to Use This Guide Related DocumentsFor Refer to Following conventions are used in this guide Conventions Used in This GuideGetting Help For information about Refer to IntroductionOverview of DFE-Gold PoE Module Capabilities DFE-Gold Module4H4285-49 DFE-Gold Module 4H4285-49 DFE-Gold Module Management Switch Configuration Using WebViewSwitch Configuration Using CLI Commands ConnectivityStandards Compatibility Lanview Diagnostic LEDsLink Aggregation Network Requirements100BASE-TX Network 10BASE-T NetworkInstallation Installation Site Requirement Contents of DFE Module Carton QuantityUnpacking the DFE Module DFE Module Placement and Installation Rules Installing Optional Network Expansion Module NEMExample 1 -1, a Example 3 -1, C Preparing to Install the 4H4285-49 Installing 4H4285-49 into a Matrix E7 or N7 Chassis Preparing to Install the 4H4285-49 Card guides Installing 4H4285-49 into Matrix N3 or N5 Chassis Card guides Connecting 48 Vdc Power for PoE Operation Connecting to the Network Connecting UTP Cables to 4H4285-49Making the UTP Connections Connecting a Twisted Pair Segment with RJ45 Connector RX+ TX+ RX+ Verifying PoE Port Status Connecting to COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Parameter Setting Connecting to a VT Series Terminal10 Connecting a VT Series Terminal Connecting to a Modem 11 Connecting Using a Modem RJ45 DB25 Adapter Wiring and Signal AssignmentsCOM Port Adapter Wiring and Signal Diagram RJ45 VT Series Port Adapter Wiring and Signal DiagramCompleting the Installation Completing the Installation of a New SystemModem Port Adapter Wiring and Signal Diagram RJ45 DB25 First-Time Log-In Using a Console Port Connection 12 Matrix Defogged Startup Screen Example N7 Chassis Enter Logging in with an Administratively-Configured User AccountCompleting the Installation Troubleshooting Using LanviewAbout the Management Mgmt LED Lanview LEDs Viewing Receive/Transmit ActivityColor State Recommended Action Viewing the PoE Port StatusAlternately 67% on, 33% LED RX/TX Refer to the Matrix DFE-Gold Series Configuration Troubleshooting ChecklistMatrix DFE-Gold Series Configuration Guide for OFFLINE/RESET Switch Overview of DFE Module Shutdown ProcedureLast Resort Shutdown Procedure Using OFFLINE/RESET Switch Recommended Shutdown Procedure Using OFFLINE/RESET SwitchSpecifications 4H4285-49 SpecificationsTable A-1 4H4285-49 Specifications Processors/Memory Table A-1 4H4285-49 Specifications ItemSpecificationTable A-3 Compliance Standards Regulatory Compliance Table A-2 COM Port Pin Assignments Signal Name Input/OutputCOM Port Pinout Assignments Regulatory ComplianceRegulatory Compliance Specifications Required Tools Mode Switch Settings and Option InstallationsSetting the Mode Switches Memory Locations and Replacement Procedures Memory Locations and Replacement ProceduresGaining Access to Memory Modules Gaining Access to Memory ModulesRemoving the Safety Cover Figure B-3 Removing the Safety Cover Removing the Network Expansion Module NEM Dram Simm Replacement ProcedureFigure B-5 Removing the Existing Dram Simm Removing the Dram SimmFigure B-6 Installing the Dram Simm Installing the Dram SimmRemoving the Dimm Dimm Replacement ProcedureFigure B-8 Installing the Dimm Installing the DimmFigure B-9 Installing the Network Expansion Module Reinstalling the Optional Network Expansion ModuleReinstalling the Safety Cover Figure B-10 Installing the Safety Cover Overview About PoE Power over EthernetFront Panel 48 Vdc Interface Power InterfaceProprietary PD Detection Matrix N5 Backplane 48 Vdc InterfaceTable C-2 PoE Status LED Indications PoE Port Status PoE Port Status LEDsPoE Port Status LEDs About PoE Power over Ethernet Numerics IndexPinout assignments console port A-3
Related manuals
Manual 56 pages 18.08 Kb