Digi manual N t e n t s, Chapter Introduction, Chapter Configuring Wireless

Page 3

	C o n t e n t s
Chapter 1	Introduction
Setup Overview		9
Step A: Plan		9
Step B: Set Up the Hardware		9
Step C: Install and Setup Digi Port Authority-Remote		9
Step D: Configure an IP Address		9
Step E: Configure Ports		9
Step F: Configure Other Features as Required		10
About Entering Commands on the Command Line		10
Supported Devices		10
About This Guide		10
Purpose		10
Audience		10
Scope		10
Other Documents in the Library		10
Device Server Quick Start Guide		10
Digi One/PortServer TS Command Reference		11
RealPort Setup Guides		11
Online Help for the Web UI		11
About Configuration Methods		11
Configure the device server with the wizard		11
Configuring the device server from an Attached Terminal		11
Configuring the device server from a Telnet Session		11
Configuring the device server from the Web Interface		11
Downloading a Configuration File		11
Configuration Prerequisites		12
Accessing the Command Line from a Locally-Connected Terminal		12
Log On as Root from the Command Line		12
Accessing the Command Line from a Telnet Session		12
Accessing the Configuration from the Web Interface		12
Chapter 2	Configuring Wireless
Configuration Considerations		13
Install Radio		13
Using Ethernet		13
Chapter 3 Configuring the IP Address
Options for Configuring the IP Address and Mask		19
Device Support: Digi Port Authority-Remote and ARP-Ping for IP Address
Configuration		19
Configuring the Ethernet Interface with Digi Port Authority-Remote ...		19
Starting Point		19
Procedure		20
Configuring the IP Address Using ARP-Ping		20
Starting Point		20
Procedure		20
Configuring the Ethernet Interface from the Command Line		21
Contents		3

Image 3

Contents Digi TS W Family 9000329B Chapter Introduction Chapter Configuring WirelessConfiguring the IP Address N t e n t sChapter Configuring Autoconnection Setting Up RealPortConfiguring the Serial Ports Chapter Configuring PPPConfiguring Security Features Configuring IP RoutingConfiguring Users Configuring the Digi Device for IAIndustrial AutomationConfiguring DNS Configuring SnmpReference and Certifications Configuring Power Over the Serial PortsContents T r o d u c t i o n Setup OverviewOther Documents in the Library About Entering Commands on the Command LineSupported Devices About This GuideAbout Configuration Methods Configuration Prerequisites N f i g u r i n g W i r e l e s s Configuration ConsiderationsSelect Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless N f i g u r i n g t h e I P a d d r e s s Options for Configuring the IP Address and MaskConfiguring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp About RealPort T t i n g U p R e a l P o r tSetting Up RealPort Configuring the Serial Port Settings with the Web Interface Options for Configuring the Serial PortsConfiguring the Serial Port Settings from the Command Line N f i g u r i n g P P P Configuring Inbound PPP ConnectionsConfiguring Outbound PPP Connections Command Line Configuring Inbound PPP Connections ExampleProcedure Sample Use the following table for additional configurations Configuring PPP D e m E m u l a t i o n Modem Emulation Digi One TS and PortServer TS 2/4 MEI onlyCommon User Scenarios Serial Device Digi Device Server Modem Emulation Cable SignalsApplication AT Com Digi Device Server Response Mand Originating, Answering, and Disconnecting CallsServer. P represents a one second pause Code Modem Emulation AT Command Set Function ResultATP Function ResultATXn Accepted but ignored There is no Nvram support currently AT+MS Ascii Registers Function Range Units Saved DefaultRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation N f i g u r i n g a u t o c o n n e c t i o n Configuring a Port for Autoconnection Web InterfaceCommands for Configuring Autoconnection by Port or by User Configuring a User for Autoconnection Web InterfaceClick Change Profile Configuring TCP Socket CommunicationConfiguring UDP Multicast Click Serial PortsClick Change Profile and select UDP Socket Configuring Autoconnection N f i g u r i n g I P R o u t i n g Configuring Static RoutesConfiguring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing Controlling Access to the Configuration Controlling Access to Inbound PortsN f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the Command Line Controlling Access to Outbound PortsIssuing User Passwords Configuring SSH Version 2 for Secure CommunicationDevice Required Hardware Firmware Http Controlling Access to ServicesSnmp SSH Configuring Security Features Configuring the User-Defined Protocol Configuring ModbusConfiguring the Digi Device for IA Industrial Automation About the Domain Name System N f i g u r i n g D N SConfiguration Procedures About Snmp and the Device Server Agent N f i g u r i n g S N M PMIB Configuration Procedure Web InterfaceN f i g u r i n g U s e r s About Configuring UsersCommon User Features Feature Description Set user FieldConfiguring a User Web Interface Commands for Configuring a UserClick New User Upgrading the Firmware Copying the Configuration to and from a Remote HostResetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Configuring RI Power Serial Power FeatureConfiguring DTR Power DTR on DTR OFF Serial Power TableConfiguring Power Over the Serial Ports F e r e n c e a n d C e r t i f i c a t i o n s Interpreting the LEDsColor State Indicates RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Environmental CertificationsDigi Contact Information Digi Contacts Reference and Certifications