Digi W manual RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex

Page 80

Device Server EIA 232/422/485 Switch Settings

Function			Switch Settings

	1	2		3	4
	1	2		3	4

EIA-232	Up	Down		Down	Down

EIA-422/485 Full-duplex	Down	Up		Down	If up, termination.
					If down,
EIA-485 half-duplex	Down	Down		Up	If down,
EIA-485 half-duplex	Down	Down		Up	no termination

RJ-45 Pinouts

	RJ-45	EIA-232	EIA-422/485	EIA-485 Half-
	Pin	EIA-232	Full-Duplex	Duplex
	Pin		Full-Duplex	Duplex

	1	RI	TxD-	TxD-

	2	DSR	RxD-	RxD-

	3	RTS	RTS+	NA

	4	GND	GND	GND

	5	TxD	TxD+	TxD+

	6	RxD	RxD+	RxD+

	7	SG	SG	SG

	8	CTS	CTS+	NA

	9	DTR	RTS-	NA

	10	DCD	CTS-	NA

WARNING: To prevent electric shock, do not remove the cover of this module while unit is powered up. There are no user-serviceable parts inside. Refer servicing to qualified personnel.

CAUTION: This unit has two power inputs. For total isolation from electrical shock and energy hazard, disconnect both power inputs. The device is intended to be mounted in an indoor only type system.

80	Chapter 19 Reference and Certifications

Image 80

Contents Digi TS W Family 9000329B Chapter Configuring Wireless Configuring the IP AddressN t e n t s Chapter IntroductionSetting Up RealPort Configuring the Serial PortsChapter Configuring PPP Chapter Configuring AutoconnectionConfiguring IP Routing Configuring Security FeaturesConfiguring the Digi Device for IAIndustrial Automation Configuring DNSConfiguring Snmp Configuring UsersConfiguring Power Over the Serial Ports Reference and CertificationsContents Setup Overview T r o d u c t i o nAbout Entering Commands on the Command Line Supported DevicesAbout This Guide Other Documents in the LibraryAbout Configuration Methods Configuration Prerequisites Configuration Considerations N f i g u r i n g W i r e l e s sSelect Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless Options for Configuring the IP Address and Mask N f i g u r i n g t h e I P a d d r e s sConfiguring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp T t i n g U p R e a l P o r t About RealPortSetting Up RealPort Options for Configuring the Serial Ports Configuring the Serial Port Settings with the Web InterfaceConfiguring the Serial Port Settings from the Command Line Configuring Inbound PPP Connections N f i g u r i n g P P PConfiguring Inbound PPP Connections Example Configuring Outbound PPP Connections Command LineProcedure Sample Use the following table for additional configurations Configuring PPP Common User Scenarios D e m E m u l a t i o nModem Emulation Digi One TS and PortServer TS 2/4 MEI only Modem Emulation Cable Signals Serial Device Digi Device ServerOriginating, Answering, and Disconnecting Calls Application AT Com Digi Device Server Response MandServer. P represents a one second pause Modem Emulation AT Command Set Function Result CodeFunction Result ATPATXn Accepted but ignored There is no Nvram support currently AT+MS Registers Function Range Units Saved Default AsciiRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation Configuring a Port for Autoconnection Web Interface Commands for Configuring Autoconnection by Port or by UserConfiguring a User for Autoconnection Web Interface N f i g u r i n g a u t o c o n n e c t i o nConfiguring TCP Socket Communication Configuring UDP MulticastClick Serial Ports Click Change ProfileClick Change Profile and select UDP Socket Configuring Autoconnection Configuring Static Routes N f i g u r i n g I P R o u t i n gConfiguring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing N f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the ConfigurationControlling Access to Inbound Ports Controlling Access to Outbound Ports Controlling Access to the Command LineDevice Required Hardware Firmware Issuing User PasswordsConfiguring SSH Version 2 for Secure Communication Controlling Access to Services HttpSnmp SSH Configuring Security Features Configuring Modbus Configuring the User-Defined ProtocolConfiguring the Digi Device for IA Industrial Automation N f i g u r i n g D N S About the Domain Name SystemConfiguration Procedures N f i g u r i n g S N M P About Snmp and the Device Server AgentConfiguration Procedure Web Interface MIBAbout Configuring Users Common User FeaturesFeature Description Set user Field N f i g u r i n g U s e r sClick New User Configuring a User Web InterfaceCommands for Configuring a User Copying the Configuration to and from a Remote Host Upgrading the FirmwareResetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Serial Power Feature Configuring RI PowerConfiguring DTR Power Serial Power Table DTR on DTR OFFConfiguring Power Over the Serial Ports Color State Indicates F e r e n c e a n d C e r t i f i c a t i o n sInterpreting the LEDs RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Certifications EnvironmentalDigi Contact Information Digi Contacts Reference and Certifications