Digi W manual Setting Up RealPort, Configuring the Serial Ports, Chapter Configuring PPP

Page 4

Manual Configuration Procedure		21
Example to Set IP Address		21
Example to Set Subnet Mask		21
Example to Set Gateway Mask		21
Manual Configuration Example		21
Configuring an IP Address using DHCP and RARP		22
About DHCP and RARP		22
Procedure		22
Chapter 4 Setting Up RealPort
About RealPort		23
What is RealPort?		23
RealPort Advantages		23
Configuring the RealPort Software		23
Chapter 5 Configuring the Serial Ports
Options for Configuring the Serial Ports		25
Configuring the Serial Port Settings with the Web Interface		25
Configuring the Serial Port Settings from the Command Line		26
Chapter 6	Configuring PPP
Configuring Inbound PPP Connections		27
Procedure for Command Line		27
Configuring Outbound PPP Connections: Command Line		28
Filters for PPP Connections		31
Chapter 7	Modem Emulation
Modem Emulation (Digi One TS and PortServer TS 2/4 MEI only)		33
Common User Scenarios		33
Modem Emulation Cable Signals		34
Originating, Answering, and Disconnecting Calls		35
Disconnecting Calls-Digi Device Server		36
Modem Emulation AT Command Set		37
S-Registers		42
Result Codes		47
Chapter 8	Configuring Autoconnection
About Autoconnection		49
Configuring a Port for Autoconnection: Web Interface		49
Commands for Configuring Autoconnection by Port or by User		49
Configuring a User for Autoconnection: Web Interface		49
Configuring TCP Socket Communication		50
Procedure for Configuring Inbound and Outbound Socket Communication		50
Configuring UDP Multicast		50
Procedure for Configuring Inbound or Outbound Socket Communication		51

4

Contents

Image 4

Contents Digi TS W Family 9000329B Chapter Configuring Wireless Configuring the IP AddressN t e n t s Chapter IntroductionSetting Up RealPort Configuring the Serial PortsChapter Configuring PPP Chapter Configuring AutoconnectionConfiguring IP Routing Configuring Security FeaturesConfiguring the Digi Device for IAIndustrial Automation Configuring DNSConfiguring Snmp Configuring UsersConfiguring Power Over the Serial Ports Reference and CertificationsContents Setup Overview T r o d u c t i o nAbout Entering Commands on the Command Line Supported DevicesAbout This Guide Other Documents in the LibraryAbout Configuration Methods Configuration Prerequisites Configuration Considerations N f i g u r i n g W i r e l e s sSelect Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless Options for Configuring the IP Address and Mask N f i g u r i n g t h e I P a d d r e s sConfiguring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp T t i n g U p R e a l P o r t About RealPortSetting Up RealPort Options for Configuring the Serial Ports Configuring the Serial Port Settings with the Web InterfaceConfiguring the Serial Port Settings from the Command Line Configuring Inbound PPP Connections N f i g u r i n g P P PConfiguring Inbound PPP Connections Example Configuring Outbound PPP Connections Command LineProcedure Sample Use the following table for additional configurations Configuring PPP Modem Emulation Digi One TS and PortServer TS 2/4 MEI only D e m E m u l a t i o nCommon User Scenarios Modem Emulation Cable Signals Serial Device Digi Device ServerOriginating, Answering, and Disconnecting Calls Application AT Com Digi Device Server Response MandServer. P represents a one second pause Modem Emulation AT Command Set Function Result CodeFunction Result ATPATXn Accepted but ignored There is no Nvram support currently AT+MS Registers Function Range Units Saved Default AsciiRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation Configuring a Port for Autoconnection Web Interface Commands for Configuring Autoconnection by Port or by UserConfiguring a User for Autoconnection Web Interface N f i g u r i n g a u t o c o n n e c t i o nConfiguring TCP Socket Communication Configuring UDP MulticastClick Serial Ports Click Change ProfileClick Change Profile and select UDP Socket Configuring Autoconnection Configuring Static Routes N f i g u r i n g I P R o u t i n gConfiguring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing Controlling Access to Inbound Ports Controlling Access to the ConfigurationN f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to Outbound Ports Controlling Access to the Command LineConfiguring SSH Version 2 for Secure Communication Issuing User PasswordsDevice Required Hardware Firmware Controlling Access to Services HttpSnmp SSH Configuring Security Features Configuring Modbus Configuring the User-Defined ProtocolConfiguring the Digi Device for IA Industrial Automation N f i g u r i n g D N S About the Domain Name SystemConfiguration Procedures N f i g u r i n g S N M P About Snmp and the Device Server AgentConfiguration Procedure Web Interface MIBAbout Configuring Users Common User FeaturesFeature Description Set user Field N f i g u r i n g U s e r sCommands for Configuring a User Configuring a User Web InterfaceClick New User Copying the Configuration to and from a Remote Host Upgrading the FirmwareResetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Serial Power Feature Configuring RI PowerConfiguring DTR Power Serial Power Table DTR on DTR OFFConfiguring Power Over the Serial Ports Interpreting the LEDs F e r e n c e a n d C e r t i f i c a t i o n sColor State Indicates RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Certifications EnvironmentalDigi Contact Information Digi Contacts Reference and Certifications