Digi W manual There is no Nvram support currently

Page 40

AT

Function

Result

Command

Code

 

 

 

 

AT&Mn

Accepted but ignored.

OK n=0, 1, 2

ERROR

 

 

Otherwise

AT&Pn

Accepted but ignored.

OK n=0, 1, 2

ERROR

 

 

Otherwise

AT&Qn

Accepted but ignored.

OK n=0 to 8

ERROR

 

 

Otherwise

 

RTS/CTS Option

 

 

This selects how the Digi Device Server controls CTS. CTS is modified if

 

 

hardware flow control is selected (see &K command). The parameter value,

 

 

if valid, is written to S21 bit2.

 

 

&R0CTS reflects the ability of the modem to transmit data. For example,

OK n=0 or 1

AT&Rn

CTS will drop during retrains. In sync mode, CTS tracks the state of RTS;

ERROR

the RTS-to-CTS delay is defined by S26. In async mode, CTS is normally

 

Otherwise

 

ON and will turn OFF only if required by flow control.

 

 

 

&R1CTS forced on (default). In sync mode, CTS is always ON (RTS transi-

 

 

tions are ignored). tracks the state of RTS. In async mode, CTS is normally

 

 

ON and will turn OFF only if required by flow control.

 

 

&R2CTS follows RTS.

 

 

DSR Override

 

 

This command selects how the modem will control DSR. The parameter

OK n=0 or 1

AT&Sn

value, if valid, is written to S21 bit 6.

ERROR

&S0DSR will remain ON at all times. (Default.)

 

Otherwise

 

&S1DSR will become active after answer tone has been detected and inac-

 

 

 

tive after the carrier has been lost.

 

AT&Tn

Accepted but ignored.

OK n= 0

ERROR

 

 

Otherwise

AT&V

Display Current Configuration and Stored Profiles

OK

There is no NVRAM support currently.

 

 

AT&Vn

Accepted but ignored.

OK n=0 to 5

ERROR

 

 

Otherwise

AT&V6

Display current IP settings of the Device Server

OK

AT&Wn

Accepted but ignored.

OK n=0 or 1

ERROR

 

 

Otherwise

AT&Xn

Accepted but ignored.

OK n=0 or 1

ERROR

 

 

Otherwise

AT&Yn

Accepted but ignored.

OK n=0 or 1

ERROR Other-

 

 

wise

AT&Zn

&Zn=x - Store Telephone Number.

OK n=0 or 3

ERROR

Currently not supported

 

Otherwise

 

 

AT\An

Accepted but ignored.

OK n=0 to 3

ERROR

 

 

Otherwise

40

Chapter 9 Modem Emulation

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Digi TS W Family 9000329B Chapter Configuring Wireless Configuring the IP AddressN t e n t s Chapter IntroductionSetting Up RealPort Configuring the Serial PortsChapter Configuring PPP Chapter Configuring AutoconnectionConfiguring IP Routing Configuring Security FeaturesConfiguring the Digi Device for IAIndustrial Automation Configuring DNSConfiguring Snmp Configuring UsersConfiguring Power Over the Serial Ports Reference and CertificationsContents Setup Overview T r o d u c t i o nAbout Entering Commands on the Command Line Supported DevicesAbout This Guide Other Documents in the LibraryAbout Configuration Methods Configuration Prerequisites Configuration Considerations N f i g u r i n g W i r e l e s sSelect Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless Options for Configuring the IP Address and Mask N f i g u r i n g t h e I P a d d r e s sConfiguring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp T t i n g U p R e a l P o r t About RealPortSetting Up RealPort Options for Configuring the Serial Ports Configuring the Serial Port Settings with the Web InterfaceConfiguring the Serial Port Settings from the Command Line Configuring Inbound PPP Connections N f i g u r i n g P P PConfiguring Inbound PPP Connections Example Configuring Outbound PPP Connections Command LineProcedure Sample Use the following table for additional configurations Configuring PPP Modem Emulation Digi One TS and PortServer TS 2/4 MEI only D e m E m u l a t i o nCommon User Scenarios Modem Emulation Cable Signals Serial Device Digi Device ServerOriginating, Answering, and Disconnecting Calls Application AT Com Digi Device Server Response MandServer. P represents a one second pause Modem Emulation AT Command Set Function Result CodeFunction Result ATPATXn Accepted but ignored There is no Nvram support currently AT+MS Registers Function Range Units Saved Default AsciiRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation Configuring a Port for Autoconnection Web Interface Commands for Configuring Autoconnection by Port or by UserConfiguring a User for Autoconnection Web Interface N f i g u r i n g a u t o c o n n e c t i o nConfiguring TCP Socket Communication Configuring UDP MulticastClick Serial Ports Click Change ProfileClick Change Profile and select UDP Socket Configuring Autoconnection Configuring Static Routes N f i g u r i n g I P R o u t i n gConfiguring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing Controlling Access to Inbound Ports Controlling Access to the ConfigurationN f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to Outbound Ports Controlling Access to the Command LineConfiguring SSH Version 2 for Secure Communication Issuing User PasswordsDevice Required Hardware Firmware Controlling Access to Services HttpSnmp SSH Configuring Security Features Configuring Modbus Configuring the User-Defined ProtocolConfiguring the Digi Device for IA Industrial Automation N f i g u r i n g D N S About the Domain Name SystemConfiguration Procedures N f i g u r i n g S N M P About Snmp and the Device Server AgentConfiguration Procedure Web Interface MIBAbout Configuring Users Common User FeaturesFeature Description Set user Field N f i g u r i n g U s e r sCommands for Configuring a User Configuring a User Web InterfaceClick New User Copying the Configuration to and from a Remote Host Upgrading the FirmwareResetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Serial Power Feature Configuring RI PowerConfiguring DTR Power Serial Power Table DTR on DTR OFFConfiguring Power Over the Serial Ports Interpreting the LEDs F e r e n c e a n d C e r t i f i c a t i o n sColor State Indicates RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Certifications EnvironmentalDigi Contact Information Digi Contacts Reference and Certifications
Top Page Image Contents