Digi W manual Serial Power Table, DTR on DTR OFF

Page 77

instructions to reset.

From the command line use the two examples below for additional information.

display circuitbreaker

Display the status of the circuit breaker

set configuration circuitbreaker=reset

Reset the circuit breaker

Note: set configuration print will also give the status of the circuitbreaker state.

Serial Power Table

Use this table for summary information for a serial power setup.

.

Quick Summary

DTR Power

RI Power

Table for Setup of

OUT

OUT

IN

Serial Power

 

 

 

 

 

 

 

Switch Settings

 

 

 

 

 

 

 

DTR setting

DTR ON

DTR OFF

DTR OFF

 

 

 

 

Ports Allowed

1, 2, 3, 4

1*, 2, 3, 4

1

*unless port 1 is used

 

 

for power in

 

 

 

 

 

 

P-6 jumper on pins

P-6 jumper on pins

P-6 jumper on pins

Jumper Pin Settings

2 & 3

2 & 3

1 & 2

 

(Factory Default)

(Factory Default)

 

 

 

 

 

 

Power Budget

9v @ up to 100mA

5v @ up to 200 mA

9 -30 v @ up to

one watt

one watt

525mA (max)

 

 

 

 

 

Chapter 18 Configuring Power Over the Serial Ports

77

Page 76 Page 78
Image 77
Page 76 Page 78
Contents Digi TS W Family 9000329B Configuring the IP Address Chapter Configuring WirelessN t e n t s Chapter IntroductionConfiguring the Serial Ports Setting Up RealPortChapter Configuring PPP Chapter Configuring AutoconnectionConfiguring Security Features Configuring IP RoutingConfiguring DNS Configuring the Digi Device for IAIndustrial AutomationConfiguring Snmp Configuring UsersReference and Certifications Configuring Power Over the Serial PortsContents T r o d u c t i o n Setup OverviewSupported Devices About Entering Commands on the Command LineAbout This Guide Other Documents in the LibraryAbout Configuration Methods Configuration Prerequisites N f i g u r i n g W i r e l e s s Configuration ConsiderationsSelect Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless N f i g u r i n g t h e I P a d d r e s s Options for Configuring the IP Address and MaskConfiguring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp About RealPort T t i n g U p R e a l P o r tSetting Up RealPort Configuring the Serial Port Settings with the Web Interface Options for Configuring the Serial PortsConfiguring the Serial Port Settings from the Command Line N f i g u r i n g P P P Configuring Inbound PPP ConnectionsConfiguring Outbound PPP Connections Command Line Configuring Inbound PPP Connections ExampleProcedure Sample Use the following table for additional configurations Configuring PPP Common User Scenarios D e m E m u l a t i o nModem Emulation Digi One TS and PortServer TS 2/4 MEI only Serial Device Digi Device Server Modem Emulation Cable SignalsApplication AT Com Digi Device Server Response Mand Originating, Answering, and Disconnecting CallsServer. P represents a one second pause Code Modem Emulation AT Command Set Function ResultATP Function ResultATXn Accepted but ignored There is no Nvram support currently AT+MS Ascii Registers Function Range Units Saved DefaultRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation Commands for Configuring Autoconnection by Port or by User Configuring a Port for Autoconnection Web InterfaceConfiguring a User for Autoconnection Web Interface N f i g u r i n g a u t o c o n n e c t i o nConfiguring UDP Multicast Configuring TCP Socket CommunicationClick Serial Ports Click Change ProfileClick Change Profile and select UDP Socket Configuring Autoconnection N f i g u r i n g I P R o u t i n g Configuring Static RoutesConfiguring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing N f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the ConfigurationControlling Access to Inbound Ports Controlling Access to the Command Line Controlling Access to Outbound PortsDevice Required Hardware Firmware Issuing User PasswordsConfiguring SSH Version 2 for Secure Communication Http Controlling Access to ServicesSnmp SSH Configuring Security Features Configuring the User-Defined Protocol Configuring ModbusConfiguring the Digi Device for IA Industrial Automation About the Domain Name System N f i g u r i n g D N SConfiguration Procedures About Snmp and the Device Server Agent N f i g u r i n g S N M PMIB Configuration Procedure Web InterfaceCommon User Features About Configuring UsersFeature Description Set user Field N f i g u r i n g U s e r sClick New User Configuring a User Web InterfaceCommands for Configuring a User Upgrading the Firmware Copying the Configuration to and from a Remote HostResetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Configuring RI Power Serial Power FeatureConfiguring DTR Power DTR on DTR OFF Serial Power TableConfiguring Power Over the Serial Ports Color State Indicates F e r e n c e a n d C e r t i f i c a t i o n sInterpreting the LEDs RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Environmental CertificationsDigi Contact Information Digi Contacts Reference and Certifications
Top Page Image Contents