Digi manual Configuring a User Web Interface, Click New User, Commands for Configuring a User

Page 70

Configuring a User: Web Interface

Use this section to configure users with from the web interface.

1.Access the web interface by entering the device server IP address in a browser’s URL window.

2.Log on to the device server as root. The default password is dbps.

3.Click Users under Configuration.

4.Click New User.

5.Enter the user name and password (password is optional).

6.Select the profile for user.

7.Enter appropriate parameters, click Next, and verify settings.

Note: If the user profile is Custom there are no parmeters to set. Click Finish if user name is correct.

8. Click Finish to save settings.

Note: To edit a user go to the Users page and click on the user name you wish to edit, enter the parameters and click Apply.

The Advanced tab under User allows you to set Escape characters for Connect, Telnet, Rlogin, and Kill as well as an SSH Public Key. Click Apply to save the settings.

Commands for Configuring a User

Use the commands listed below as well as find specific examples and complete parameters from the Digi One/PortServer TS Command Reference.

•set user (name=)

•newpass to assign a password

•default access=menu to configure a user for a menu

•autoconnect to automatically connect a user

•remove to remove a user from the user table

70	Chapter 16 Configuring Users

Image 70

Contents Digi TS W Family 9000329B N t e n t s Chapter Configuring WirelessConfiguring the IP Address Chapter IntroductionChapter Configuring PPP Setting Up RealPortConfiguring the Serial Ports Chapter Configuring AutoconnectionConfiguring IP Routing Configuring Security FeaturesConfiguring Snmp Configuring the Digi Device for IAIndustrial AutomationConfiguring DNS Configuring UsersConfiguring Power Over the Serial Ports Reference and CertificationsContents Setup Overview T r o d u c t i o nAbout This Guide About Entering Commands on the Command LineSupported Devices Other Documents in the LibraryAbout Configuration Methods Configuration Prerequisites Configuration Considerations N f i g u r i n g W i r e l e s sSelect Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless Options for Configuring the IP Address and Mask N f i g u r i n g t h e I P a d d r e s sConfiguring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp T t i n g U p R e a l P o r t About RealPortSetting Up RealPort Options for Configuring the Serial Ports Configuring the Serial Port Settings with the Web InterfaceConfiguring the Serial Port Settings from the Command Line Configuring Inbound PPP Connections N f i g u r i n g P P PConfiguring Inbound PPP Connections Example Configuring Outbound PPP Connections Command LineProcedure Sample Use the following table for additional configurations Configuring PPP Modem Emulation Digi One TS and PortServer TS 2/4 MEI only D e m E m u l a t i o nCommon User Scenarios Modem Emulation Cable Signals Serial Device Digi Device ServerOriginating, Answering, and Disconnecting Calls Application AT Com Digi Device Server Response MandServer. P represents a one second pause Modem Emulation AT Command Set Function Result CodeFunction Result ATPATXn Accepted but ignored There is no Nvram support currently AT+MS Registers Function Range Units Saved Default AsciiRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation Configuring a User for Autoconnection Web Interface Configuring a Port for Autoconnection Web InterfaceCommands for Configuring Autoconnection by Port or by User N f i g u r i n g a u t o c o n n e c t i o nClick Serial Ports Configuring TCP Socket CommunicationConfiguring UDP Multicast Click Change ProfileClick Change Profile and select UDP Socket Configuring Autoconnection Configuring Static Routes N f i g u r i n g I P R o u t i n gConfiguring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing Controlling Access to Inbound Ports Controlling Access to the ConfigurationN f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to Outbound Ports Controlling Access to the Command LineConfiguring SSH Version 2 for Secure Communication Issuing User PasswordsDevice Required Hardware Firmware Controlling Access to Services HttpSnmp SSH Configuring Security Features Configuring Modbus Configuring the User-Defined ProtocolConfiguring the Digi Device for IA Industrial Automation N f i g u r i n g D N S About the Domain Name SystemConfiguration Procedures N f i g u r i n g S N M P About Snmp and the Device Server AgentConfiguration Procedure Web Interface MIBFeature Description Set user Field About Configuring UsersCommon User Features N f i g u r i n g U s e r sCommands for Configuring a User Configuring a User Web InterfaceClick New User Copying the Configuration to and from a Remote Host Upgrading the FirmwareResetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Serial Power Feature Configuring RI PowerConfiguring DTR Power Serial Power Table DTR on DTR OFFConfiguring Power Over the Serial Ports Interpreting the LEDs F e r e n c e a n d C e r t i f i c a t i o n sColor State Indicates RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Certifications EnvironmentalDigi Contact Information Digi Contacts Reference and Certifications