Digi W manual Certifications, Environmental

Page 81

Standard Models Specifications

Power Requirements

(Standard Models)

2-contact barrel

connector

+9 to +30 VDC 525 mA (max) external power supply

Environmental

Ambient

0 to 50° Celsius

temperature

32 to 131° Fahrenheit

 

 

 

Relative

5% to 90% non-condensing

humidity

 

 

 

Altitude

0 to 12,000 feet

0 to 3,658 meters

 

 

 

 

Mechanical

 

 

Length

13.33 centimeters

5.25 inches

 

 

 

Width

8.25 centimeters

3.25 inches

 

 

 

Height

3.842 centimeters

1.306 inches

 

 

 

Weight

.227 Kilos

8 ounces

 

 

 

Certifications

FCC Part 15 Class A

Radio Frequency Interference (RFI) (FCC 15.105)

This equipment has been tested and found to comply with the limits for Class A digital devices pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

Chapter 19 Reference and Certifications

81

Page 80 Page 82
Image 81
Page 80 Page 82
Contents Digi TS W Family 9000329B Configuring the IP Address Chapter Configuring WirelessN t e n t s Chapter IntroductionConfiguring the Serial Ports Setting Up RealPortChapter Configuring PPP Chapter Configuring AutoconnectionConfiguring Security Features Configuring IP RoutingConfiguring DNS Configuring the Digi Device for IAIndustrial AutomationConfiguring Snmp Configuring UsersReference and Certifications Configuring Power Over the Serial PortsContents T r o d u c t i o n Setup OverviewSupported Devices About Entering Commands on the Command LineAbout This Guide Other Documents in the LibraryAbout Configuration Methods Configuration Prerequisites N f i g u r i n g W i r e l e s s Configuration ConsiderationsSelect Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless N f i g u r i n g t h e I P a d d r e s s Options for Configuring the IP Address and MaskConfiguring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp About RealPort T t i n g U p R e a l P o r tSetting Up RealPort Configuring the Serial Port Settings with the Web Interface Options for Configuring the Serial PortsConfiguring the Serial Port Settings from the Command Line N f i g u r i n g P P P Configuring Inbound PPP ConnectionsConfiguring Outbound PPP Connections Command Line Configuring Inbound PPP Connections ExampleProcedure Sample Use the following table for additional configurations Configuring PPP D e m E m u l a t i o n Modem Emulation Digi One TS and PortServer TS 2/4 MEI onlyCommon User Scenarios Serial Device Digi Device Server Modem Emulation Cable SignalsApplication AT Com Digi Device Server Response Mand Originating, Answering, and Disconnecting CallsServer. P represents a one second pause Code Modem Emulation AT Command Set Function ResultATP Function ResultATXn Accepted but ignored There is no Nvram support currently AT+MS Ascii Registers Function Range Units Saved DefaultRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation Commands for Configuring Autoconnection by Port or by User Configuring a Port for Autoconnection Web InterfaceConfiguring a User for Autoconnection Web Interface N f i g u r i n g a u t o c o n n e c t i o nConfiguring UDP Multicast Configuring TCP Socket CommunicationClick Serial Ports Click Change ProfileClick Change Profile and select UDP Socket Configuring Autoconnection N f i g u r i n g I P R o u t i n g Configuring Static RoutesConfiguring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing Controlling Access to the Configuration Controlling Access to Inbound PortsN f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the Command Line Controlling Access to Outbound PortsIssuing User Passwords Configuring SSH Version 2 for Secure CommunicationDevice Required Hardware Firmware Http Controlling Access to ServicesSnmp SSH Configuring Security Features Configuring the User-Defined Protocol Configuring ModbusConfiguring the Digi Device for IA Industrial Automation About the Domain Name System N f i g u r i n g D N SConfiguration Procedures About Snmp and the Device Server Agent N f i g u r i n g S N M PMIB Configuration Procedure Web InterfaceCommon User Features About Configuring UsersFeature Description Set user Field N f i g u r i n g U s e r sConfiguring a User Web Interface Commands for Configuring a UserClick New User Upgrading the Firmware Copying the Configuration to and from a Remote HostResetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Configuring RI Power Serial Power FeatureConfiguring DTR Power DTR on DTR OFF Serial Power TableConfiguring Power Over the Serial Ports F e r e n c e a n d C e r t i f i c a t i o n s Interpreting the LEDsColor State Indicates RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Environmental CertificationsDigi Contact Information Digi Contacts Reference and Certifications
Top Page Image Contents