Digi W manual Issuing User Passwords, Configuring SSH Version 2 for Secure Communication

Page 59

•By user where a user is required to login and may be required to supply a password, but once the user is authenticated, an automatic connection to a host is made.

For information on configuring autoconnection, see "Configuring

Autoconnection" on page 49.

Method 2: Menus

Menus select destination systems without having to access the device server command line. For information on configuring menus, see the description of the set menu command in the Digi One/PortServer TS Command Reference.

Issuing User Passwords

This section discusses how to issue user passwords.

Related Information

See the newpass and set user commands in the Digi One/PortServer TS Command Reference.

Starting Point

This procedure assumes that you have signed on as root and already configured the user to whom you will be issuing a password.

The Advanced tab under User allows you to set Escape characters for Connect, Telnet, Rlogin, and Kill as well as an SSH Public Key. Click Apply to save the settings.

Procedure

1.Issue a newpass command that identifies the user (on the name field) to whom this password will be issued.

2.When the system prompts you for a new password, type in the pass- word and then press Enter.

3.When the system prompts you to enter the new password again, type it in and then press Enter.

Configuring SSH Version 2 for Secure Communication

This section discusses how to configure a user for SSH version 2 encryption.

This feature is only available for the following devices.

	Device	Required	Required
	Device	Hardware	Firmware
		Hardware	Firmware

	Digi One TS	50000771-01A or higher

	PortServer TS 2 MEI	50000771-02A or higher	82000747a or higher
			82000747a or higher
	PortServer TS 4 MEI &	50000771-03A or higher
	Wireless	50000771-03A or higher
	Wireless

Chapter 12 Configuring Security Features

59

Image 59

Contents Digi TS W Family 9000329B Chapter Introduction Chapter Configuring WirelessConfiguring the IP Address N t e n t sChapter Configuring Autoconnection Setting Up RealPortConfiguring the Serial Ports Chapter Configuring PPPConfiguring Security Features Configuring IP RoutingConfiguring Users Configuring the Digi Device for IAIndustrial AutomationConfiguring DNS Configuring SnmpReference and Certifications Configuring Power Over the Serial PortsContents T r o d u c t i o n Setup OverviewOther Documents in the Library About Entering Commands on the Command LineSupported Devices About This GuideAbout Configuration Methods Configuration Prerequisites N f i g u r i n g W i r e l e s s Configuration ConsiderationsSelect Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless N f i g u r i n g t h e I P a d d r e s s Options for Configuring the IP Address and MaskConfiguring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp About RealPort T t i n g U p R e a l P o r tSetting Up RealPort Configuring the Serial Port Settings with the Web Interface Options for Configuring the Serial PortsConfiguring the Serial Port Settings from the Command Line N f i g u r i n g P P P Configuring Inbound PPP ConnectionsConfiguring Outbound PPP Connections Command Line Configuring Inbound PPP Connections ExampleProcedure Sample Use the following table for additional configurations Configuring PPP Common User Scenarios D e m E m u l a t i o nModem Emulation Digi One TS and PortServer TS 2/4 MEI only Serial Device Digi Device Server Modem Emulation Cable SignalsApplication AT Com Digi Device Server Response Mand Originating, Answering, and Disconnecting CallsServer. P represents a one second pause Code Modem Emulation AT Command Set Function ResultATP Function ResultATXn Accepted but ignored There is no Nvram support currently AT+MS Ascii Registers Function Range Units Saved DefaultRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation N f i g u r i n g a u t o c o n n e c t i o n Configuring a Port for Autoconnection Web InterfaceCommands for Configuring Autoconnection by Port or by User Configuring a User for Autoconnection Web InterfaceClick Change Profile Configuring TCP Socket CommunicationConfiguring UDP Multicast Click Serial PortsClick Change Profile and select UDP Socket Configuring Autoconnection N f i g u r i n g I P R o u t i n g Configuring Static RoutesConfiguring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing N f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the ConfigurationControlling Access to Inbound Ports Controlling Access to the Command Line Controlling Access to Outbound PortsDevice Required Hardware Firmware Issuing User PasswordsConfiguring SSH Version 2 for Secure Communication Http Controlling Access to ServicesSnmp SSH Configuring Security Features Configuring the User-Defined Protocol Configuring ModbusConfiguring the Digi Device for IA Industrial Automation About the Domain Name System N f i g u r i n g D N SConfiguration Procedures About Snmp and the Device Server Agent N f i g u r i n g S N M PMIB Configuration Procedure Web InterfaceN f i g u r i n g U s e r s About Configuring UsersCommon User Features Feature Description Set user FieldClick New User Configuring a User Web InterfaceCommands for Configuring a User Upgrading the Firmware Copying the Configuration to and from a Remote HostResetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Configuring RI Power Serial Power FeatureConfiguring DTR Power DTR on DTR OFF Serial Power TableConfiguring Power Over the Serial Ports Color State Indicates F e r e n c e a n d C e r t i f i c a t i o n sInterpreting the LEDs RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Environmental CertificationsDigi Contact Information Digi Contacts Reference and Certifications