Digi W manual Configuring IP Routing, Configuring Security Features

Page 5

Chapter 9 Configuring IP Routing
Configuring Static Routes	53
Related Information	53
Procedure	53
Example: Route Using the Ethernet Interface	53
Example: Route Using a PPP Link	53
Configuring Dynamic Routes Using RIP	54
Related Information	54
Starting Point	54
Procedure	54
Example: Dynamic Routes	54
Configuring Proxy ARP	55
Related Information	55
Starting Point	55
Procedure	55
Example	55
Chapter 10 Configuring Security Features
Controlling Access to the Configuration	57
Controlling Access to Inbound Ports	57
Default Access Restrictions	57
Options for Removing Access Restriction	57
Procedure for Changing a Port’s Access Requirements	57
Example:	58
Procedure for Changing a User’s Access Requirements	58
Example:	58
Controlling Access to Outbound Ports	58
Default Access	58
Restricting Access to Outbound Ports	58
CHAP Authentication for PPP Users	58
Controlling Access to the Command Line	58
Autoconnection	58
Method 2: Menus	59
Issuing User Passwords	59
Related Information	59
Starting Point	59
Procedure	59
Configuring SSH Version 2 for Secure Communication	59
Password Protection	60
Using a Public Key	60
Making Reverse SSH Connections to Ports	60
Controlling Access to Services	60
Services that Can Be Turned Off	60
Service Levels	61
Procedure	61

Contents

5

Image 5

Contents Digi TS W Family 9000329B Configuring the IP Address Chapter Configuring WirelessN t e n t s Chapter IntroductionConfiguring the Serial Ports Setting Up RealPortChapter Configuring PPP Chapter Configuring AutoconnectionConfiguring Security Features Configuring IP RoutingConfiguring DNS Configuring the Digi Device for IAIndustrial AutomationConfiguring Snmp Configuring UsersReference and Certifications Configuring Power Over the Serial PortsContents T r o d u c t i o n Setup OverviewSupported Devices About Entering Commands on the Command LineAbout This Guide Other Documents in the LibraryAbout Configuration Methods Configuration Prerequisites N f i g u r i n g W i r e l e s s Configuration ConsiderationsSelect Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless N f i g u r i n g t h e I P a d d r e s s Options for Configuring the IP Address and MaskConfiguring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp About RealPort T t i n g U p R e a l P o r tSetting Up RealPort Configuring the Serial Port Settings with the Web Interface Options for Configuring the Serial PortsConfiguring the Serial Port Settings from the Command Line N f i g u r i n g P P P Configuring Inbound PPP ConnectionsConfiguring Outbound PPP Connections Command Line Configuring Inbound PPP Connections ExampleProcedure Sample Use the following table for additional configurations Configuring PPP Common User Scenarios D e m E m u l a t i o nModem Emulation Digi One TS and PortServer TS 2/4 MEI only Serial Device Digi Device Server Modem Emulation Cable SignalsApplication AT Com Digi Device Server Response Mand Originating, Answering, and Disconnecting CallsServer. P represents a one second pause Code Modem Emulation AT Command Set Function ResultATP Function ResultATXn Accepted but ignored There is no Nvram support currently AT+MS Ascii Registers Function Range Units Saved DefaultRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation Commands for Configuring Autoconnection by Port or by User Configuring a Port for Autoconnection Web InterfaceConfiguring a User for Autoconnection Web Interface N f i g u r i n g a u t o c o n n e c t i o nConfiguring UDP Multicast Configuring TCP Socket CommunicationClick Serial Ports Click Change ProfileClick Change Profile and select UDP Socket Configuring Autoconnection N f i g u r i n g I P R o u t i n g Configuring Static RoutesConfiguring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing N f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the ConfigurationControlling Access to Inbound Ports Controlling Access to the Command Line Controlling Access to Outbound PortsDevice Required Hardware Firmware Issuing User PasswordsConfiguring SSH Version 2 for Secure Communication Http Controlling Access to ServicesSnmp SSH Configuring Security Features Configuring the User-Defined Protocol Configuring ModbusConfiguring the Digi Device for IA Industrial Automation About the Domain Name System N f i g u r i n g D N SConfiguration Procedures About Snmp and the Device Server Agent N f i g u r i n g S N M PMIB Configuration Procedure Web InterfaceCommon User Features About Configuring UsersFeature Description Set user Field N f i g u r i n g U s e r sClick New User Configuring a User Web InterfaceCommands for Configuring a User Upgrading the Firmware Copying the Configuration to and from a Remote HostResetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Configuring RI Power Serial Power FeatureConfiguring DTR Power DTR on DTR OFF Serial Power TableConfiguring Power Over the Serial Ports Color State Indicates F e r e n c e a n d C e r t i f i c a t i o n sInterpreting the LEDs RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Environmental CertificationsDigi Contact Information Digi Contacts Reference and Certifications