Digi W manual Click Change Profile and select UDP Socket

Page 51

Procedure for Configuring Inbound or Outbound Socket Communication

1.Access the web interface by entering the device server IP address in a browser’s URL window.

2.Log on to the Digi One/PortServer TS as root. The default password is dbps.

3.Click Serial Ports.

4.Click the port number you want to configure.

5.Click Change Profile and select UDP Socket

Note: The serial parameters for two connecting devices must match meaning if one device is set for 9600 bps, the other device must be set for the same rate.

6.Fill in the requested information and click Apply to save the settings.

7.Repeat these steps until you have added the necessary destinations. Use the context sensitive Help for additional information.

Chapter 10 Configuring Autoconnection

51

Image 51

Contents Digi TS W Family 9000329B Chapter Introduction Chapter Configuring WirelessConfiguring the IP Address N t e n t sChapter Configuring Autoconnection Setting Up RealPortConfiguring the Serial Ports Chapter Configuring PPPConfiguring Security Features Configuring IP RoutingConfiguring Users Configuring the Digi Device for IAIndustrial AutomationConfiguring DNS Configuring SnmpReference and Certifications Configuring Power Over the Serial PortsContents T r o d u c t i o n Setup OverviewOther Documents in the Library About Entering Commands on the Command LineSupported Devices About This GuideAbout Configuration Methods Configuration Prerequisites N f i g u r i n g W i r e l e s s Configuration ConsiderationsSelect Discover Digi Device from the CD Configuring Wireless Configuring Wireless Configuring Wireless Configuring Wireless N f i g u r i n g t h e I P a d d r e s s Options for Configuring the IP Address and MaskConfiguring the IP Address Using ARP-Ping Configuring the Ethernet Interface from the Command Line Configuring an IP Address using Dhcp and Rarp About RealPort T t i n g U p R e a l P o r tSetting Up RealPort Configuring the Serial Port Settings with the Web Interface Options for Configuring the Serial PortsConfiguring the Serial Port Settings from the Command Line N f i g u r i n g P P P Configuring Inbound PPP ConnectionsConfiguring Outbound PPP Connections Command Line Configuring Inbound PPP Connections ExampleProcedure Sample Use the following table for additional configurations Configuring PPP D e m E m u l a t i o n Modem Emulation Digi One TS and PortServer TS 2/4 MEI onlyCommon User Scenarios Serial Device Digi Device Server Modem Emulation Cable SignalsApplication AT Com Digi Device Server Response Mand Originating, Answering, and Disconnecting CallsServer. P represents a one second pause Code Modem Emulation AT Command Set Function ResultATP Function ResultATXn Accepted but ignored There is no Nvram support currently AT+MS Ascii Registers Function Range Units Saved DefaultRegister Function Range Units Saved Default Register Function Range Units Saved Default 17 11h =XON/XOFF &K4 Result Codes Short Long Form Modem Emulation N f i g u r i n g a u t o c o n n e c t i o n Configuring a Port for Autoconnection Web InterfaceCommands for Configuring Autoconnection by Port or by User Configuring a User for Autoconnection Web InterfaceClick Change Profile Configuring TCP Socket CommunicationConfiguring UDP Multicast Click Serial PortsClick Change Profile and select UDP Socket Configuring Autoconnection N f i g u r i n g I P R o u t i n g Configuring Static RoutesConfiguring Dynamic Routes Using RIP Configuring Proxy ARP Configuring IP Routing Controlling Access to the Configuration Controlling Access to Inbound PortsN f i g u r i n g S e c u r i t y F e a t u r e s Controlling Access to the Command Line Controlling Access to Outbound PortsIssuing User Passwords Configuring SSH Version 2 for Secure CommunicationDevice Required Hardware Firmware Http Controlling Access to ServicesSnmp SSH Configuring Security Features Configuring the User-Defined Protocol Configuring ModbusConfiguring the Digi Device for IA Industrial Automation About the Domain Name System N f i g u r i n g D N SConfiguration Procedures About Snmp and the Device Server Agent N f i g u r i n g S N M PMIB Configuration Procedure Web InterfaceN f i g u r i n g U s e r s About Configuring UsersCommon User Features Feature Description Set user FieldConfiguring a User Web Interface Commands for Configuring a UserClick New User Upgrading the Firmware Copying the Configuration to and from a Remote HostResetting Device Server Configuration to Defaults Commands for Resetting the Configuration to Defaults Managing the OS and Configuration Configuring RI Power Serial Power FeatureConfiguring DTR Power DTR on DTR OFF Serial Power TableConfiguring Power Over the Serial Ports F e r e n c e a n d C e r t i f i c a t i o n s Interpreting the LEDsColor State Indicates RJ-45 Pinouts EIA-232 EIA-422/485 EIA-485 Half Full-Duplex Environmental CertificationsDigi Contact Information Digi Contacts Reference and Certifications