Cypress CY7C1318JV18, CY7C1316JV18, CY7C1320JV18 Write Cycle Descriptions, BWS0 BWS1, NWS0 NWS1

CY7C1316JV18, CY7C1916JV18

CY7C1318JV18, CY7C1320JV18

Truth Table

The truth table for the CY7C1316JV18, CY7C1916JV18, CY7C1318JV18, and CY7C1320JV18 follows. [2, 3, 4, 5, 6, 7]

Operation			K	LD	R/W	DQ		DQ
Write Cycle:			L-H	L	L	D(A1) at K(t + 1) ↑		D(A2) at
									K(t + 1) ↑
Load address; wait one cycle;
input write data on consecutive K and	K	rising edges.
Read Cycle:			L-H	L	H	Q(A1) at		Q(A2) at C(t + 2) ↑
							C(t + 1)↑
Load address; wait one and a half cycle;
read data on consecutive C and C rising edges.
NOP: No Operation			L-H	H	X	High-Z		High-Z
Standby: Clock Stopped			Stopped	X	X	Previous State		Previous State

Burst Address Table

(CY7C1318JV18, CY7C1320JV18)

First Address (External)	Second Address (Internal)
X..X0	X..X1
X..X1	X..X0

Write Cycle Descriptions

The write cycle description table for CY7C1316JV18 and CY7C1318JV18 follows. [2, 8]

BWS0/	BWS1/		K			Comments
					K
NWS0		NWS1
L		L	L–H		–	During the data portion of a write sequence:
						CY7C1316JV18 − both nibbles (D[7:0]) are written into the device.
						CY7C1318JV18 − both bytes (D[17:0]) are written into the device.
L		L	–	L-H		During the data portion of a write sequence:
						CY7C1316JV18 − both nibbles (D[7:0]) are written into the device.
						CY7C1318JV18 − both bytes (D[17:0]) are written into the device.
L		H	L–H		–	During the data portion of a write sequence:
						CY7C1316JV18 − only the lower nibble (D[3:0]) is written into the device, D[7:4]		remains unaltered.
						CY7C1318JV18 − only the lower byte (D[8:0]) is written into the device, D[17:9]	remains unaltered.
L		H	–	L–H		During the data portion of a write sequence:
						CY7C1316JV18 − only the lower nibble (D[3:0]) is written into the device, D[7:4]		remains unaltered.
						CY7C1318JV18 − only the lower byte (D[8:0]) is written into the device, D[17:9]	remains unaltered.
H		L	L–H		–	During the data portion of a write sequence:
						CY7C1316JV18 − only the upper nibble (D[7:4]) is written into the device, D[3:0]		remains unaltered.
						CY7C1318JV18 − only the upper byte (D[17:9]) is written into the device, D[8:0]	remains unaltered.
H		L	–	L–H		During the data portion of a write sequence:
						CY7C1316JV18 − only the upper nibble (D[7:4]) is written into the device, D[3:0]		remains unaltered.
						CY7C1318JV18 − only the upper byte (D[17:9]) is written into the device, D[8:0]	remains unaltered.
H		H	L–H		–	No data is written into the devices during this portion of a write operation.
H		H	–	L–H		No data is written into the devices during this portion of a write operation.

Notes

2.X = “Don’t Care,” H = Logic HIGH, L = Logic LOW, ↑ represents rising edge.

3.Device powers up deselected with the outputs in a tri-state condition.

4.On CY7C1318JV18 and CY7C1320JV18, “A1” represents address location latched by the devices when transaction was initiated and “A2” represents the addresses sequence in the burst. On CY7C1316JV18 and CY7C1916JV18, “A1” represents A + ‘0’ and “A2” represents A + ‘1’.

5.“t” represents the cycle at which a read/write operation is started. t + 1 and t + 2 are the first and second clock cycles succeeding the “t” clock cycle.

6.Data inputs are registered at K and K rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode.

7.It is recommended that K = K and C = C = HIGH when clock is stopped. This is not essential, but permits most rapid restart by overcoming transmission line charging symmetrically.

8.Is based on a write cycle that was initiated in accordance with the Write Cycle Descriptions table. NWS0, NWS1, BWS0, BWS1, BWS2, and BWS3 can be altered on different portions of a write cycle, as long as the setup and hold requirements are achieved.

Document Number: 001-15271 Rev. *B Page 10 of 26

[+] Feedback