B&B Electronics I-7011 user manual Quick Start, Default Setting, Jumper Setting

Page 14

1.6 Quick Start

Refer to “I-7000 Bus Converter User Manual” and “Get-

ting Start” for more detail.

1.7 Default Setting

Default setting for I-7011/11D/11P/11PD/18/18P :

zAddress : 01

zAnalog Input Type : Type 05, -2.5 to +2.5 V

zBaudrate : 9600 bps

zChecksum disable, 60Hz rejection, engineer unit format

zI-7018/18P set as INIT* mode, and the analog input is 6 dif- ferential and 2 single-ended.

1.8 Jumper Setting

I-7018/18P : Jumper JP1 for select the pin INIT*/Vin 7- Select 8 differential mode, the pin INIT*/Vin7- is set to Vin7-

Select INIT* mode, the pin INIT*/Vin7- is set to INIT*

I-7011, I-7018 User Manual

Rev:B1.0

Image 14

Contents Trademark WarrantyCopyright Table of Contents @AADOData High/Low Alarm Introduction More InformationPin Assignment RevB1.0 Specifications 7011/I-7011D7011P/I-7011PD 7018 7018PBlock Diagram Wire Connection Page Quick Start Default SettingJumper Setting Calibration Don’t Perform Calibrate Until You Really UnderstandData Format Setting FF Configuration TablesBaudrate Setting CC Analog Input Type Setting TT Analog input type and data format table Type Input Range Data Format +F.S Zero CodeRevB1.0 Type Input Range Data Format +F.S Zero Code Command Sec.2.19 AACHKcr Related CommandSyntax %AANNTTCCFFCHKcr ?AACHKcrSyntax #**CHKcr Example#AA Syntax #AACHKcrSyntax #AANCHKcr Response Valid Command DataCHKcr Invalid Command ?AACHKcr#AAN $AA0 Syntax $AA0CHKcr$AA1 Syntax $AA1CHKcrAATTCCFFCHKcr $AA2Syntax $AA2CHKcr FF data format of module reference Sec.1.10 Example$AA3 Syntax $AA3CHKcrAASDataCHKcr $AA4Syntax $AA4CHKcr Data synchronized data, format reference Sec.1.10 Example10 $AA5VV Syntax $AA5VVCHKcrAAVVCHKcr 11 $AA6Syntax $AA6CHKcr AAVCHKcr 12 $AA8Syntax $AA8CHKcr 13 $AA8V Syntax $AA8VCHKcrSyntax $AA9DataCHKcr Related Command Sec.2.8 $AA314 $AA9Data AA address of response module 00 to FF ExampleAASCHKcr 15 $AABSyntax $AABCHKcr AADataCHKcr 16 $AAFSyntax $AAFCHKcr 17 $AAM Syntax $AAMCHKcr18 $AAZData Syntax $AAZDataCHKcrSyntax ~AAODataCHKcr Read address 01 module name, return 7018. Related Command19 ~AAOData Related Topic 20 ~AAEVSyntax ~AAEVCHKcr AASOOIICHKcr 21 @AADISyntax @AADICHKcr Level. ExampleHigh 22 @AADOData 23 @AAEAT Syntax @AAEATCHKcr24 @AAHIData 25 @AALOData Syntax @AADACHKcr Related Command Sec.2.23 @AAEAT Related Topic26 @AADA 27 @AACA Syntax @AACACHKcrSyntax @AARHCHKcr Read address 01 high alarm, return +2.5000. Related Command28 @AARH 29 @AARL Syntax @AARECHKcr Read address 01 event counter, return 1234. Related Command30 @AARE 31 @AACE Syntax @AACECHKcrSyntax ~**CHKcr 32 ~Description Host OK Response No response. ExampleSyntax ~AA0CHKcr Host watchdog timeout flag, 0=Clear, 1=Set Example33 ~AA0 AASSCHKcr34 ~AA1 Syntax ~AA1CHKcr35 ~AA2 Syntax ~AA2CHKcr36 ~AA3EVV Syntax ~AA3EVVCHKcrAAPPSSCHKcr 37 ~AA4Syntax ~AA4CHKcr SS Safe Value, data format is same as PP Example38 ~AA5PPSS Syntax ~AA5PPSSCHKcrINIT* pin Operation Module StatusDigital Output Dual Watchdog OperationDigital Input and Event Counter Dual Watchdog = Module Watchdog + Host WatchdogHigh/Low Alarm Thermocouple Measurement