B&B Electronics I-7011 user manual 13 $AA8V, Syntax $AA8VCHKcr

Page 34

2.13 $AA8V

Description : Set LED Configuration

Syntax : $AA8V[CHK](cr)

$

delimiter character

AA

address of setting module (00 to FF)

8command for setting LED configuration

V 1=Set LED to module, 2=Set LED to host

Response : Valid Command :

!AA[CHK](cr)

 

Invalid Command :

?AA[CHK](cr)

 

Syntax error or communication error may get no re-

 

sponse.

 

!

delimiter for valid command

 

?delimiter for invalid command

AAaddress of response module(00 to FF) Example :

Command : $0182

Receive : !01

Set address 01 LED to host control, return success.

Command : $0281

Receive : !02

Set address 02 LED to module control, return success. Related Command :

Sec2.12 $AA8, Sec2.18 $AAZ(Data)

Note : The command is for I-7011D/11PD only

34

I-7011, I-7018 User Manual

Rev:B1.0

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Copyright WarrantyTrademark Table of Contents @AADOData High/Low Alarm Introduction More InformationPin Assignment RevB1.0 Specifications 7011/I-7011D7011P/I-7011PD 7018 7018PBlock Diagram Wire Connection Page Jumper Setting Default SettingQuick Start Calibration Don’t Perform Calibrate Until You Really UnderstandBaudrate Setting CC Analog Input Type Setting TT Configuration TablesData Format Setting FF Analog input type and data format table Type Input Range Data Format +F.S Zero CodeRevB1.0 Type Input Range Data Format +F.S Zero Code Command Sec.2.19 AACHKcr Related CommandSyntax %AANNTTCCFFCHKcr ?AACHKcrSyntax #**CHKcr Example#AA Syntax #AACHKcr#AAN Response Valid Command DataCHKcr Invalid Command ?AACHKcrSyntax #AANCHKcr $AA0 Syntax $AA0CHKcr$AA1 Syntax $AA1CHKcrAATTCCFFCHKcr $AA2Syntax $AA2CHKcr FF data format of module reference Sec.1.10 Example$AA3 Syntax $AA3CHKcrAASDataCHKcr $AA4Syntax $AA4CHKcr Data synchronized data, format reference Sec.1.10 Example10 $AA5VV Syntax $AA5VVCHKcrSyntax $AA6CHKcr 11 $AA6AAVVCHKcr Syntax $AA8CHKcr 12 $AA8AAVCHKcr 13 $AA8V Syntax $AA8VCHKcrSyntax $AA9DataCHKcr Related Command Sec.2.8 $AA314 $AA9Data AA address of response module 00 to FF ExampleSyntax $AABCHKcr 15 $AABAASCHKcr Syntax $AAFCHKcr 16 $AAFAADataCHKcr 17 $AAM Syntax $AAMCHKcr18 $AAZData Syntax $AAZDataCHKcr19 ~AAOData Read address 01 module name, return 7018. Related CommandSyntax ~AAODataCHKcr Syntax ~AAEVCHKcr 20 ~AAEVRelated Topic AASOOIICHKcr 21 @AADISyntax @AADICHKcr Level. ExampleHigh 22 @AADOData 23 @AAEAT Syntax @AAEATCHKcr24 @AAHIData 25 @AALOData 26 @AADA Related Command Sec.2.23 @AAEAT Related TopicSyntax @AADACHKcr 27 @AACA Syntax @AACACHKcr28 @AARH Read address 01 high alarm, return +2.5000. Related CommandSyntax @AARHCHKcr 29 @AARL 30 @AARE Read address 01 event counter, return 1234. Related CommandSyntax @AARECHKcr 31 @AACE Syntax @AACECHKcrSyntax ~**CHKcr 32 ~Description Host OK Response No response. ExampleSyntax ~AA0CHKcr Host watchdog timeout flag, 0=Clear, 1=Set Example33 ~AA0 AASSCHKcr34 ~AA1 Syntax ~AA1CHKcr35 ~AA2 Syntax ~AA2CHKcr36 ~AA3EVV Syntax ~AA3EVVCHKcrAAPPSSCHKcr 37 ~AA4Syntax ~AA4CHKcr SS Safe Value, data format is same as PP Example38 ~AA5PPSS Syntax ~AA5PPSSCHKcrINIT* pin Operation Module StatusDigital Output Dual Watchdog OperationDigital Input and Event Counter Dual Watchdog = Module Watchdog + Host WatchdogHigh/Low Alarm Thermocouple Measurement
Top Page Image Contents