B&B Electronics I-7011 user manual INIT* pin Operation, Module Status

Page 61

3. Application Note

3.1 INIT* pin Operation

Each I-7000 module has a build-in EEPROM to store con- figuration information such as address, type, baudrate and other information. Sometimes, user may forget the configuration of the module. Therefore, the I-7000 have a special mode named “INIT mode”, to help user to resolve the problem. The “INIT mode” is setting as Address=00, baudrate=9600bps, no checksum

To enable INIT mode, please follow these steps: Step1. Power off the module

Step2. Connect the INIT* pin with the GND pin. Step3. Power on

Step4. Send command $002(cr) in 9600bps to read the configura- tion stored in the module’s EEPROM.

Refer to “7000 Bus Converter User ManualSec.5.1 and “Getting Start” for more information.

3.2 Module Status

PowerOn Reset or Module Watchdog Reset will let all output goto PowerOn Value. And the module may accept the host’s command to change the output value.

Host Watchdog Timeout will let all digital output goto Safe Value.The host watchdog timeout flag is set, and the output command will be ignored. The module’s LED will go to flash and user must reset the Module Status via command to restore normal operation.

Rev:B1.0

I-7011, I-7018 User Manual

61

Image 61
Contents Copyright WarrantyTrademark Table of Contents @AADOData High/Low Alarm More Information IntroductionPin Assignment RevB1.0 7011/I-7011D Specifications7011P/I-7011PD 7018P 7018Block Diagram Wire Connection Page Jumper Setting Default SettingQuick Start Don’t Perform Calibrate Until You Really Understand CalibrationBaudrate Setting CC Analog Input Type Setting TT Configuration TablesData Format Setting FF Type Input Range Data Format +F.S Zero Code Analog input type and data format tableRevB1.0 Type Input Range Data Format +F.S Zero Code Command Sec.2.19 Syntax %AANNTTCCFFCHKcr Related CommandAACHKcr ?AACHKcrExample Syntax #**CHKcrSyntax #AACHKcr #AA#AAN Response Valid Command DataCHKcr Invalid Command ?AACHKcrSyntax #AANCHKcr Syntax $AA0CHKcr $AA0Syntax $AA1CHKcr $AA1Syntax $AA2CHKcr $AA2AATTCCFFCHKcr FF data format of module reference Sec.1.10 ExampleSyntax $AA3CHKcr $AA3Syntax $AA4CHKcr $AA4AASDataCHKcr Data synchronized data, format reference Sec.1.10 ExampleSyntax $AA5VVCHKcr 10 $AA5VVSyntax $AA6CHKcr 11 $AA6AAVVCHKcr Syntax $AA8CHKcr 12 $AA8AAVCHKcr Syntax $AA8VCHKcr 13 $AA8V14 $AA9Data Related Command Sec.2.8 $AA3Syntax $AA9DataCHKcr AA address of response module 00 to FF ExampleSyntax $AABCHKcr 15 $AABAASCHKcr Syntax $AAFCHKcr 16 $AAFAADataCHKcr Syntax $AAMCHKcr 17 $AAMSyntax $AAZDataCHKcr 18 $AAZData19 ~AAOData Read address 01 module name, return 7018. Related CommandSyntax ~AAODataCHKcr Syntax ~AAEVCHKcr 20 ~AAEVRelated Topic Syntax @AADICHKcr 21 @AADIAASOOIICHKcr Level. ExampleHigh 22 @AADOData Syntax @AAEATCHKcr 23 @AAEAT24 @AAHIData 25 @AALOData 26 @AADA Related Command Sec.2.23 @AAEAT Related TopicSyntax @AADACHKcr Syntax @AACACHKcr 27 @AACA28 @AARH Read address 01 high alarm, return +2.5000. Related CommandSyntax @AARHCHKcr 29 @AARL 30 @AARE Read address 01 event counter, return 1234. Related CommandSyntax @AARECHKcr Syntax @AACECHKcr 31 @AACEDescription Host OK 32 ~Syntax ~**CHKcr Response No response. Example33 ~AA0 Host watchdog timeout flag, 0=Clear, 1=Set ExampleSyntax ~AA0CHKcr AASSCHKcrSyntax ~AA1CHKcr 34 ~AA1Syntax ~AA2CHKcr 35 ~AA2Syntax ~AA3EVVCHKcr 36 ~AA3EVVSyntax ~AA4CHKcr 37 ~AA4AAPPSSCHKcr SS Safe Value, data format is same as PP ExampleSyntax ~AA5PPSSCHKcr 38 ~AA5PPSSModule Status INIT* pin OperationDigital Input and Event Counter Dual Watchdog OperationDigital Output Dual Watchdog = Module Watchdog + Host WatchdogThermocouple Measurement High/Low Alarm