B&B Electronics user manual Specifications, 7011/I-7011D

Page 8

1.3 Specifications

I-7011/I-7011D

 

 

Analog Input

 

Logic Level 0 : +1V max

Input Channel :

1

Logic Level 1 : +3.5 to 30V

Input Type :

 

Event Counter

mV, V, mA(with external

Max Input Frequency : 50 Hz

125 ohms resistor)

Min. Pulse Width : 1 mS

Thermocouple : Type J, K,

Displayed LED

T, E, R, S, B, N, C

4½ digits (for I-7011D)

Sampling Rate :

 

Power Supply

10 Samples/Second

Input : +10 to +30 VDC

Bandwidth : 5.24 Hz

Consumption :

Accuracy : ±0.05%

 

0.9W for I-7011

Zero Drift : 0.5µV/°C

1.5W for I-7011D

Span Drift : 25ppm/°C

 

CMR@50/60Hz : 150dB

 

NMR@50/60Hz : 100dB

 

Input Impedance : 20M Ohms

 

Isolation : 3000VDC

Digital Output

2 channel

Open Collector to 30V Output Load : sink 30mA max Power Dissipation : 300mW

Digital Input 1 channel

8

I-7011, I-7018 User Manual

Rev:B1.0

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Trademark WarrantyCopyright Table of Contents @AADOData High/Low Alarm Introduction More InformationPin Assignment RevB1.0 Specifications 7011/I-7011D7011P/I-7011PD 7018 7018PBlock Diagram Wire Connection Page Quick Start Default SettingJumper Setting Calibration Don’t Perform Calibrate Until You Really UnderstandData Format Setting FF Configuration TablesBaudrate Setting CC Analog Input Type Setting TT Analog input type and data format table Type Input Range Data Format +F.S Zero CodeRevB1.0 Type Input Range Data Format +F.S Zero Code Command Sec.2.19 Related Command Syntax %AANNTTCCFFCHKcrAACHKcr ?AACHKcrSyntax #**CHKcr Example#AA Syntax #AACHKcrSyntax #AANCHKcr Response Valid Command DataCHKcr Invalid Command ?AACHKcr#AAN $AA0 Syntax $AA0CHKcr$AA1 Syntax $AA1CHKcr$AA2 Syntax $AA2CHKcrAATTCCFFCHKcr FF data format of module reference Sec.1.10 Example$AA3 Syntax $AA3CHKcr$AA4 Syntax $AA4CHKcrAASDataCHKcr Data synchronized data, format reference Sec.1.10 Example10 $AA5VV Syntax $AA5VVCHKcrAAVVCHKcr 11 $AA6Syntax $AA6CHKcr AAVCHKcr 12 $AA8Syntax $AA8CHKcr 13 $AA8V Syntax $AA8VCHKcrRelated Command Sec.2.8 $AA3 14 $AA9DataSyntax $AA9DataCHKcr AA address of response module 00 to FF ExampleAASCHKcr 15 $AABSyntax $AABCHKcr AADataCHKcr 16 $AAFSyntax $AAFCHKcr 17 $AAM Syntax $AAMCHKcr18 $AAZData Syntax $AAZDataCHKcrSyntax ~AAODataCHKcr Read address 01 module name, return 7018. Related Command19 ~AAOData Related Topic 20 ~AAEVSyntax ~AAEVCHKcr 21 @AADI Syntax @AADICHKcrAASOOIICHKcr Level. ExampleHigh 22 @AADOData 23 @AAEAT Syntax @AAEATCHKcr24 @AAHIData 25 @AALOData Syntax @AADACHKcr Related Command Sec.2.23 @AAEAT Related Topic26 @AADA 27 @AACA Syntax @AACACHKcrSyntax @AARHCHKcr Read address 01 high alarm, return +2.5000. Related Command28 @AARH 29 @AARL Syntax @AARECHKcr Read address 01 event counter, return 1234. Related Command30 @AARE 31 @AACE Syntax @AACECHKcr32 ~ Description Host OKSyntax ~**CHKcr Response No response. ExampleHost watchdog timeout flag, 0=Clear, 1=Set Example 33 ~AA0Syntax ~AA0CHKcr AASSCHKcr34 ~AA1 Syntax ~AA1CHKcr35 ~AA2 Syntax ~AA2CHKcr36 ~AA3EVV Syntax ~AA3EVVCHKcr37 ~AA4 Syntax ~AA4CHKcrAAPPSSCHKcr SS Safe Value, data format is same as PP Example38 ~AA5PPSS Syntax ~AA5PPSSCHKcrINIT* pin Operation Module StatusDual Watchdog Operation Digital Input and Event CounterDigital Output Dual Watchdog = Module Watchdog + Host WatchdogHigh/Low Alarm Thermocouple Measurement
Top Page Image Contents