Zhone Technologies Z-PLEX-10-24-DOC-SC manual Country-Specific Regulatory Compliance Information

Page 4

If this equipment (Z-Plex 10) causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes to its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice so you can make the necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, or for repair or warranty information, please contact the service center at:

Zhone Technologies, 48664 Milmont Drive, Fremont, CA., 95132, Telephone 510-353-7600

If this equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

In the event of equipment malfunction, all repairs must be performed by the equipment manufacturer, or an authorized agent. It is the responsibility of users requiring service to report the need for service to the equipment manufacturer, or to one of its authorized agents.

Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information).

Country-Specific Regulatory Compliance Information

CANADA

Industrie Canada Requirements

NOTICE TO USERS OF THE CANADIAN TELEPHONE NETWORK

The Industrie Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction.

Before installing this equipment, ensure that it is permissible to connect to the facilities of the local telecommunications company. The equipment must be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with above conditions may not prevent degradation of service in some situations.

Image 4
Contents Plex User’s Guide Trademarks Regulatory Information FCC Part 68 Regulatory InformationCountry-Specific Regulatory Compliance Information Industrie Canada RequirementsPage Page Contents Chapter Configuring the ZPlex Chapter DiagnosticsAppendix a Alphabetical Reference \ Zhone Technologies Product overview Introduction Product overviewFeatures Features IntroductionBenefits TR-08Snmp Managing the Z-PlexIntroduction Managing the Z-Plex Product specifications Product specifications Introduction2 CLI TftpIntroduction Product specifications AMI, B8ZSProduct specifications Introduction Product description Installing the Z-Plex Product descriptionBack panel Unpacking the product Front panelPacking materials Kit of partsInstalling the product Important Safety InstructionsInstalling the product Installing the Z-Plex Installing the Z-Plex Rack mounting Rack mountingLocating the product on a desktop Locating the product on a desktop Installing the Z-PlexWall mounting Electrical Installation Connector type Connector typeBackpanel connectors Data port connector pinouts Electrical Installation Data port connector pinoutsDCE DB25 data port female connector Electrical Installation Data port connector pinouts 1 FXO/FXS connectorsPair female amphenol connector Power requirements 2 RJ48 connectorPower requirements Electrical Installation T1 connector pinoutsAlarm Power installationElectrical Installation Alarm AC power installationGrounding requirements Electrical Installation Grounding requirementsCabling Electrical Installation CablingRecommended cables Cabling Electrical Installation Using the command line interface Configuring the Z-Plex Using the command line interfaceQuick start system configuration Quick start system configuration Configuring the Z-PlexConfiguring the Z-Plex Quick start system configuration Configuring a management interface Setting the dateLogging in and out of the system Configuring the local management channel Configuring the DS0 management channelConfiguring the Ethernet management channel Configuring the IP over FDL management channelConfiguring system contact information Configuring SnmpConfiguring Snmp Configuring the Z-Plex Configuring T1 interfaces Configuring the Z-Plex Configuring T1 interfacesConfiguring a T1 drop and insert interface Configuring FXS portsConfiguring FXO ports Configuring the Z-Plex Configuring FXO portsConfiguring the V.35 data port Configuring the V.35 data port Configuring the Z-PlexAdding and deleting routes Configuring the Z-Plex Adding and deleting routesAdding and deleting network routes Adding and deleting routes Configuring the Z-Plex Example routing configurationAdding and deleting host routes Example routing configuration Displaying routesRoute Display Values Displaying host routesSystem maintenance commands Rebooting the systemConfiguring the Z-Plex System maintenance commands Displaying flash informationDisplaying list of alarms Displaying and clearing list of history alarmsSystem maintenance commands Configuring the Z-Plex Displaying timeslot usageActivating code in bank Tftp downloading18 \ Zhone Technologies Diagnostics T1 loopbacks T1 loopbacksT1 loopbacks Diagnostics T1 loopbacksBER testing Diagnostics BER testingActivating a BER test for an entire T1 line Activating a BER test for individual time slotsData port loopbacks Diagnostics Data port loopbacksTesting FXO and FXS ports Diagnostics Testing FXO and FXS portsTesting FXO and FXS ports Diagnostics FXO and FXS ports loopbackConfiguring FXO loopbacks Configuring FXS loopbacksUsing test mode on the FXO and FXS ports Setting or viewing the transmit Abcd signaling bitsAlarm LED LED indicatorsDiagnostics LED indicators Power LED LED indicators DiagnosticsEthernet LED WAN LEDsConfiguration groups Table A-1. Configuration groups in the Z-PlexParameter reference Alphabetical Reference Parameter referenceParameter reference Alphabetical Reference Fxotst Alphabetic reference Allcur AllfarcurAllfartot AllfarintBES BertCLK Ctsdelay ClksrcCode CTSCUR DS0Errins DSRFDL Frame FdlipHdlc Ipfdl INTIphdl Lofc LinelenLoop FXO Loopback Loop FXSLoopback T1 Mode FXO MaskMaskfdl MaskhdlMode FXS Pattern NchanRate Rngbk RlsdRtlp FXO RxAB FXO Rtlp FXSRxAB FXS Schan SESSlip StateState FXS State FXOState T1 Syscontact SysdescrSyslocation SysnameTOT Test FXSTrcntl FXO Trnkc FXO Trcntrl FXSTrnkc FXS Trstat FXS Trstat FXOTS data port TS FXO TS FXSTsbertoff TsbertonTtlp FXO Ttlp FXSTxAB FXS TxAB FXOType FXO Type FXS Type UASWAN WAN FXOCommand reference Error messages Alphabetical Reference Error messagesQueryhalarm RebootError messages Alphabetical Reference Basic control commands Table A-4. Basic control commandsCLI reference Alphabetical Reference CLI referenceMovement and search commands CLI reference Alphabetical ReferenceTable A-5. Movement and search commands Insert and change commandsTable A-6. Insert and change commands Delete commands Put and undo commandsTable A-7. Delete commands Table A-8. Put and undo commandsUndo last command 38 \ Zhone Technologies Index LED 194-4 Index-4 / Zhone Technologies WAN LED

Z-PLEX-10-24-DOC-SC specifications

Zhone Technologies is a leading provider of innovative telecommunications and data networking solutions, and the Z-PLEX-10-24-DOC-SC is one of their advanced products designed to meet the demands of modern networking environments. This versatile optical networking solution is ideal for service providers looking to deliver high-speed broadband services to residential and business customers.

The Z-PLEX-10-24-DOC-SC provides an impressive 24-port capability, making it a robust choice for deployment in various settings, from small community networks to larger metropolitan areas. Its compact design allows for easy integration into existing systems, minimizing the need for extensive reconfiguration or additional space. The system is geared towards enabling efficient fiber deployment and helps operators enhance their service offerings while reducing operational expenses.

One of the main features of the Z-PLEX-10-24-DOC-SC is its support for Dense Wavelength Division Multiplexing (DWDM) technology. This allows multiple optical signals to be transmitted simultaneously over a single optical fiber, greatly increasing the capacity and efficiency of the network. By leveraging DWDM, service providers can maximize their existing infrastructure without the need for extensive new fiber installation.

Another significant characteristic of the Z-PLEX-10-24-DOC-SC is its scalability. The system is designed to grow with the telecommunication needs of operators, supporting various service types, including voice, video, and data, without sacrificing performance or quality. This flexibility ensures that as users' demands evolve, the Z-PLEX-10-24-DOC-SC can adapt to meet these changing requirements.

The unit also incorporates advanced management features, supported by Zhone's innovative software tools. These tools facilitate network monitoring, configuration, and maintenance, allowing operators to optimize their operations and provide better service to their end-users. This end-to-end management capability is essential in today’s fast-paced digital landscape, where customer satisfaction is paramount.

In summary, the Zhone Technologies Z-PLEX-10-24-DOC-SC is a powerful optical networking solution that combines advanced technology with scalability and efficiency. It empowers service providers to deliver high-quality broadband services while optimizing their resources. With its DWDM support, compact design, and robust management tools, the Z-PLEX-10-24-DOC-SC stands out as a reliable choice for modern telecommunications infrastructure.