Avocent KVM over IP switch 3.1 PS/2 IP-KVM switch keyboard settings, Remote Mouse Settings

Page 20

8/16 PS/2 KVM over IP switch

4.1.3.1 PS/2 IP-KVM switch keyboard settings

The PS/2 IP-KVM switch settings for the host's keyboard type have to be correct in order to make the remote keyboard work properly. Check the settings in the PS/2 IP-KVM switch front-end. See 6.3.3 for details.

4.1.3.2 Remote Mouse Settings

A common problem with KVM devices is the synchronization between the local and remote mouse cursors. The PS/2 IP-KVM switch addresses this situation with an intelligent synchronization algorithm. There are two mouse modes available on the PS/2 IP-KVM switch.

Auto mouse speed

The automatic mouse speed mode tries to detect the speed and acceleration settings of the host system automatically. See the section below for a more detailed explanation.

Fixed mouse speed

This mode just translates the mouse movements from the Remote Console in a way that one pixel move will lead to n pixel moves on the remote system. This parameter n is adjustable with the scaling. It should be noted that this works only when mouse acceleration is turned off on the remote system.

4.1.3.3 Auto mouse speed and mouse synchronization

The automatic mouse speed mode performs the speed detection during mouse synchronization. Whenever the mouse does not move correctly, there are two ways for re-synchronizing local and remote mouse:

Fast Sync

The fast synchronization is used to correct a temporary, but fixed skew. Choose the option using the Remote Console options menu or press the mouse synchronization hotkey sequence in case you defined one.

Intelligent Sync

If the fast sync does not work or the mouse settings have been changed on the host system, use the intelligent resynchronization. This method takes more time than the fast one and can be accessed with the appropriate item in the Remote Console option menu. The intelligent synchronization requires a correctly adjusted picture. Use the auto adjustment function or the manual correction in the Video Settings panel to setup the picture. The Sync mouse button on top of the Remote Console can behave differently, depending on the current state of mouse synchronization. Usually pressing this button leads to a fast sync, except in situations where the KVM port or the video mode changed recently.

Note: At first start, if the local mouse pointer is not synchronized with the remote mouse pointer, press the Auto Adjust Button once.

4.1.3.4 Host system mouse settings

The host's operating system knows various settings from the mouse driver.

Warning

The following limitations do not apply in case of USB and Mouse Type “MS Windows 2000 and newer”.

17

Page 19 Page 21
Image 20
Page 19 Page 21
Contents USER’S Manual RevTable of Contents Menu Options Quick Installation Guide InstallationInitial IP configuration Video modesWeb interface Remote Console16 PS/2 KVM over IP switch Introduction When the server is up and runningWhen the sever is dead Features Package contents Model No port PS/2 IP-KVM switch Technical specifications Model No Port PS/2 IP-KVM switchSystem requirement Model No Ports PS/2 IP-KVM switch Model No Ports PS/2 IP-KVM switchCable diagrams PS/2 Cable VGA CablePS/2 to DB9 adapter Optional Hardware installation Connecting PS/2 IP-KVM switch to the host systemOperation Overview StepLocal console Internet Connecting the External Reset/Power Option Configuration Initial ConfigurationInitial configuration via Dhcp server PS/2 IP-KVM switch Setup ToolAuthentication IP-KVM switch setup toolInitial configuration via serial console IP autoconfigurationKeyboard, Mouse and Video configuration IP address3.1 PS/2 IP-KVM switch keyboard settings Remote Mouse SettingsHost system mouse settings Auto mouse speed and mouse synchronizationWindows XP Mouse Settings Single and Double Mouse ModeRecommended Mouse Settings Special Mouse DriverTelnet UsagePrerequisites ¾ The Membrane Buttons Port PS/2 IP-KVM Switch PC port LED Indication¾ 7-Segment Bank LED Indication ¾ Reset Button Bank Bank button and PC 8/16 8/16 buttonKeyboard Hot Key Commands To select PC port To get out of Auto Scan Mode, Press any key or Space barDaisy Chain Connection Hot PlugOn Screen Display Operation 16 PS/2 KVM over IP switch Login into the PS/2 IP-KVM switch and logout Login screenNavigation MainLogout from the PS/2 IP-KVM switch Remote Console General descriptionMain Window Remote Console Control BarExclusive Access Monitor OnlyScaling Mouse HandlingVideo Settings Local CursorPhase Reset this ModeReset all Modes BrightnessSoft Keyboard Save changesUndo Changes Remote Console Status Line 14. Remote Console Confirmation DialogRemote Control KVM Console Menu Options16 PS/2 KVM over IP switch Change Password Users And GroupsKVM Settings User Console15. User Console Settings Part 16 PS/2 KVM over IP switch 17. Keyboard and Mouse Settings Keyboard/Mouse18. Video Settings Video4Device Settings Network16 PS/2 KVM over IP switch Dynamic DNS 20. Dynamic DNS16 PS/2 KVM over IP switch Security 22. Device Security23. Certificate Settings Certificate24. SSL Certificate Upload Serial Port 25. Serial Port16 PS/2 KVM over IP switch Date And Time 27. Date and TimeEvent Log 29. Event Log16 PS/2 KVM over IP switch Device Information Board SummaryReset Functions 32. Event Log ListUpdate Firmware 33. Update FirmwareUnit Reset 34. Unit ResetTroubleshooting Certificates CE CertificatePin Assignments Single port PS/2 KVM over IP Key Codes Table B.1 Key Names Video Modes
Top Page Image Contents