Motorola SBV5120 manual Introduction Installation Troubleshooting Glossary

Page 2

Introduction

Installation

Troubleshooting

Glossary

License

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THE UNIT MUST NOT BE EXPOSED TO DRIPPING OR SPLASHING. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ON THE UNIT.

CAUTION: THIS PRODUCT WAS QUALIFIED UNDER TEST CONDITIONS THAT INCLUDED THE USE OF THE SUPPLIED CABLES BETWEEN SYSTEMS COMPONENTS. TO ENSURE REGULATORY AND SAFETY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE CABLES AND INSTALL THEM PROPERLY.

CAUTION: DIFFERENT TYPES OF CORD SETS MAY BE USED FOR CONNECTIONS TO THE MAIN SUPPLY CIRCUIT. USE ONLY A MAIN LINE CORD THAT COMPLIES WITH ALL APPLICABLE PRODUCT SAFETY REQUIREMENTS OF THE COUNTRY OF USE.

CAUTION: INSTALLATION OF THIS PRODUCT MUST BE IN ACCORDANCE WITH NATIONAL WIRING CODES AND CONFORM TO LOCAL REGULATIONS.

CAUTION: DO NOT OPEN THE UNIT. DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE INSTALLATION AND TROUBLESHOOTING INSTRUCTIONS. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION: CHANGES AND MODIFICATIONS NOT EXPRESSLY APPROVED BY MOTOROLA FOR COMPLIANCE COULD VOID USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

Read all of the instructions listed here and/or in the user manual before you operate this equipment. Give particular attention to all safety precautions. Retain the instructions for future reference.

This device must be installed and used in strict accordance with manufacturer’s instructions as described in the user documentation that comes with the product.

Comply with all warning and caution statements in the instructions. Observe all warning and caution symbols that are affixed to this equipment.

Do not overload outlets or extension cords, as this can result in a risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power cords, damaged or cracked wire insulation, and broken plugs are dangerous. They may result in a shock or fire hazard.

Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords where they are attached to plugs and convenience receptacles, and examine the point where they exit from the product.

Place this equipment in a location that is close enough to an electrical outlet to accommodate the length of the power cord.

Place unit to allow for easy access when disconnecting the power cord of the device from the AC wall outlet.

Do not connect the plug into an extension cord, receptacle, other outlet unless the plug can be fully inserted with no part of the blades exposed.

Place this equipment on a stable surface.

Postpone cable modem installation until there is no risk of thunderstorm or lightning activity in the area.

Avoid using this product during an electrical storm. There may be a risk of electric shock from lightning. For added protection for this product during a lightning storm, or when it is left unattended and unused for long

Home Print

X

ii

SBV5120 Series VoIP Cable Modem User Guide

Exit

 

 

Image 2
Contents User Guide SBV5120 Series VoIP Cable Modem Introduction Installation Troubleshooting Glossary Iii FCC Compliance Class B Digital DeviceCanada Industry Canada IC Contents Faster IntroductionEasier BetterTop and Front Panel Key Light FlashingBefore You Begin Rear PanelPrecautions Always make the wall connection firstSigning Up for Service USB Connection Computer System RequirementsEthernet Card Installation and Configuration Overview Cabling and Startup for a Single UserUSB Setting Up a USB Driver Setting Up a USB Driver in Windows Introduction Installation Troubleshooting Glossary License Select The updated driver... and click Next Introduction Installation Troubleshooting Glossary License Setting Up a USB Driver in Windows Me Setting Up a USB Driver in Windows Introduction Installation Troubleshooting Glossary License Introduction Installation Troubleshooting Glossary License Setting Up a USB Driver in Windows XP Configuring TCP/IP Configuring TCP/IP in Windows 95, 98, or Windows Me Click Obtain an IP address automatically Configuring TCP/IP in Windows Introduction Installation Troubleshooting Glossary License Introduction Installation Troubleshooting Glossary License Introduction Installation Troubleshooting Glossary License Configuring TCP/IP in Windows XP Introduction Installation Troubleshooting Glossary License Introduction Installation Troubleshooting Glossary License Verifying the IP Address Verifying the IP Address in Windows 2000 or Windows XP Renewing Your IP Address Cabling for Multiple Users Ethernet and USBEthernet Troubleshooting Problem Possible SolutionsFront-Panel Lights and Error Conditions Send OnlineRemoving the USB Driver Removing the USB Driver from Windows 98 or Windows MeIntroduction Installation Troubleshooting Glossary License Click Settings Removing the USB Driver from WindowsIntroduction Installation Troubleshooting Glossary License Click Uninstall Click My ComputerClick Remove Driver Removing the USB Driver from Windows XP Introduction Installation Troubleshooting Glossary License Introduction Installation Troubleshooting Glossary License Click My Computer Contact Us If you own your SURFboard VoIP cable modemFrequently Asked Questions What type of technical support is available? What do I do if my SURFboard VoIP cable modem stops working?Glossary DocsisSoftware License SURFboard Cable ModemsGovernment Restricted Rights Visit our website at
Related manuals
Manual 56 pages 47.22 Kb