Multitech FR3060, 3100 manual MultiFRAD 3000-Series User Guide

Page 20

MultiFRAD 3000-Series User Guide

If your network protocol is IPX, continue with the following steps. If you are not using IPX routing, click on IPX Routing Enable check box to disable IPX, then click on the OK button, and proceed to step 13.

9.Router Name: You can use the default Router Name or you can assign a new Router Name in this field. If you assign a new Router Name, it must be a printable ASCII string of a maximum of 47 characters. The router name is used by the MultiFRAD to advertise its service in the IPX inter-network.

10.Ethernet: You can enable Auto Learn Network Numbers by leaving the default Yes or you can manually assign the network numbers by clicking on No in the Auto Learn Network Numbers field.

If no file server is connected to the Ethernet segment, then this field should be No (recommended).

If you enable Auto Learn (Yes), the MultiFRAD will learn the IPX network numbers from the file server.

If you select No for Auto Learn, record the network numbers assigned by the network file server for each of the four frame types (Raw (802.3), LLC (802.2), EthernetII (Type II), SNAP) in the space provided below.

RAW (802.3) Frames Network Number _____________

LCC (802.2) Frames Network Number ______________

TYPE_II Frames Network Number _________________

SNAP Frames Network Number ___________________

WAN Network Number __________________________

When you manually assigning network numbers, you must make sure they match the network numbers assigned to your local file server (if any).

11.WAN: Enter the WAN network number for the Frame Relay WAN Port by clicking on the Network Number box and back spacing through the default number and entering your new WAN Number. Make sure the WAN network number is the same as the MultiFRAD on the other end of the link.

The WAN network number has to be assigned by the Network Administrator and must be unique throughout the entire inter-network.

Note: The WAN port does not have the capability of learning the network number, unlike the LAN port (i.e., the WAN port does not have a file server).

12.Click on OK when you are satisfied with your selections.

13.If you clicked OK from the IPX Protocol Default Setup dialog box (step 8), the IP Protocol Default Setup dialog box is displayed.

20

Image 20

Contents Models FR3060/3100 User Guide User Guide Contents Appendices Introduction and Description Introduction Preview of this GuideRouter Management Front Panel Description Composite LinkVoice/Fax Channels 1 Power Connector Frame Ground GND ConnectorInternal Composite Link T1 DSU Connector Monitor XMT/RCV ConnectorChannels 3 10 Connectors Voice/Fax Channels 1 8 ConnectorsTechnical Specifications Command PortChannel Connectors Ethernet PortInstallation Safety Warnings Unpacking your MultiFRADCabling your MultiFRAD PC or Terminal UnitsMultiFRAD 3000-Series User Guide Software Loading and Configuration Loading your Software Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide MultiFRAD Software Before You Begin Setup Menu IP Setup MultiFRAD Software IPX Setup MultiFRAD Software Spanning Tree Setup Statistics IP Statistics IPX Port Statistics STP Spanning Tree Port Statistics Snmp Statistics WAN Statistics PPP Statistics Data Port Statistics Frame Relay Statistics MultiFRAD 3000-Series User Guide WAN Port Setup Point to Point Setup Frame Relay Setup MultiFRAD 3000-Series User Guide MultiFRAD Software MultiFRAD 3000-Series User Guide Frame Relay Network Data Port Configuration Remote Configuration Modem-Based Remote Configuration Procedure Remote Configuration MultiFRAD 3000-Series User Guide Remote Configuration MultiFRAD 3000-Series User Guide Router Management MultiFRAD Telnet Server Menu MultiFRAD Configuration Remote User DatabaseWEB Browser Management Router Management MultiFRAD 3000-Series User Guide Warranty, Service and Tech Support Limited Warranty On-line Warranty RegistrationContacting Tech Support via E-mail Tech SupportRecording MultiFRAD Information To log on to the Multi-Tech BBS ServiceMulti-Tech BBS To Download a file If you know the file nameAbout the Internet About the Multi-Tech Fax-Back ServiceAbout CompuServe Appendices Appendix a Cabling Diagrams Command Port Cable LAN CablesTrunk Cable RS232C/V.24 * Link CableRemote Configuration Cable Command PortAppendix B Regulatory Information Appendix C Network Overview Figure B-1. OSI Protocol StackPacket Network Address Internet Protocol IPIP Addressing MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary Subscriber Loop See Local loop Glossary MultiFRAD 3000-Series User Guide Index LEDs Index Telnet