Multitech 3100, FR3060 manual Software Loading and Configuration

Page 21

Chapter 3 - Software Loading and Configuration

14.To change the IP parameters, proceed to the next step. If you are not using IP routing, click on the IP Routing Enable check box to disable IP routing and proceed to step 20 (the WAN Ports Default Setup).

15.The default Ethernet IP Address has to be changed to your unique LAN address. Assign an acceptable unique IP address to the Ethernet port.

16.Change the default Subnet Mask and Frame Type to the values you have assigned to your LAN port.

17.The default WAN Address has to be changed to your unique WAN address. Assign an acceptable unique WAN Address to the WAN port.

18.Change the default Subnet Mask and Remote Address for WAN to the values you have assigned to your WAN.

19.Click on OK when you are satisfied with your selections.

20.The WAN Port Default Setup dialog box is displayed. The WAN Port is enabled in this dialog box. Frame Relay is also enabled. If your WAN port is going to be used in Point-to-point protocol, click on the Enable PPP. If PPP is enabled, then the Modem Command Setup field is active and either Asynchronous or Direct Connect needs to be enabled.

The WAN port can be further configured once the installation of the software is completed, by clicking on the MultiFRAD Configuration icon and clicking on the WAN button.

21.Click on the OK button in the WAN Port Default Setup dialog box.

22.The Data Port Configuration dialog box allows you to individually configure each of the ten data channels. After configuring a given channel, you may copy that channel’s configuration to any of the other channels by selecting the desired channels in the “Duplicate To” group and clicking on the “Copy” button.

If your data device is a synchronous device, ensure that the clocking and, if an internal clock is used, the Speed is correct. Also, check the Encoding Scheme, Between Frames, and InterFrame Timer are correct for your channel device. Refer to user documentation for the parameters of the channel device.

21

Image 21

Contents Models FR3060/3100 User Guide User Guide Contents Appendices Introduction and Description Preview of this Guide IntroductionRouter Management Composite Link Front Panel DescriptionVoice/Fax Channels 1 Frame Ground GND Connector Power ConnectorInternal Composite Link T1 DSU Connector Monitor XMT/RCV ConnectorVoice/Fax Channels 1 8 Connectors Channels 3 10 ConnectorsCommand Port Technical SpecificationsChannel Connectors Ethernet PortInstallation Unpacking your MultiFRAD Safety WarningsPC or Terminal Units Cabling your MultiFRADMultiFRAD 3000-Series User Guide Software Loading and Configuration Loading your Software Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide MultiFRAD Software Before You Begin Setup Menu IP Setup MultiFRAD Software IPX Setup MultiFRAD Software Spanning Tree Setup Statistics IP Statistics IPX Port Statistics STP Spanning Tree Port Statistics Snmp Statistics WAN Statistics PPP Statistics Data Port Statistics Frame Relay Statistics MultiFRAD 3000-Series User Guide WAN Port Setup Point to Point Setup Frame Relay Setup MultiFRAD 3000-Series User Guide MultiFRAD Software MultiFRAD 3000-Series User Guide Frame Relay Network Data Port Configuration Remote Configuration Modem-Based Remote Configuration Procedure Remote Configuration MultiFRAD 3000-Series User Guide Remote Configuration MultiFRAD 3000-Series User Guide Router Management MultiFRAD Telnet Server Menu Remote User Database MultiFRAD ConfigurationWEB Browser Management Router Management MultiFRAD 3000-Series User Guide Warranty, Service and Tech Support On-line Warranty Registration Limited WarrantyTech Support Recording MultiFRAD InformationContacting Tech Support via E-mail Service Multi-Tech BBSTo log on to the Multi-Tech BBS If you know the file name To Download a fileAbout the Multi-Tech Fax-Back Service About CompuServeAbout the Internet Appendices LAN Cables Appendix a Cabling Diagrams Command Port CableRS232C/V.24 * Link Cable Trunk CableCommand Port Remote Configuration CableAppendix B Regulatory Information Figure B-1. OSI Protocol Stack Appendix C Network OverviewPacket Internet Protocol IP Network AddressIP Addressing MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary Subscriber Loop See Local loop Glossary MultiFRAD 3000-Series User Guide Index LEDs Index Telnet