Multitech 3100, FR3060 manual Channels 3 10 Connectors, Voice/Fax Channels 1 8 Connectors

Page 11

Chapter 1 - Introduction and Description

Channels 3 - 10 Connectors

These DB-25 female connectors are used to connect the MultiFRAD to channel devices. These connections can be to either asynchronous or HDLC synchronous RS232 data equipment such as multiplexers.

Voice/Fax Channels 1 - 8 Connectors

Note: the Voice/Fax connectors are not currently supported.

E&M

Use the E&M connector to connect the MultiFRAD Voice/Fax channel to the E&M connector on an analog PBX (Private Branch eXchange) trunk when linking two PBX’s together. The E&M connector is an RJ-48 jack.

FXO

Use the FXO (Foreign eXchange Office) connector to connect the MultiFRAD Voice/Fax channel to an analog station card on the local PBX. This connection is also commonly referred to as an OPX (Off Premises eXtension). The FXO connector is an RJ-11 jack.

FXS

Use the FXS (Foreign eXchange Station) connector to connect the MultiFRAD Voice/Fax channel to an analog station instrument (telephone, fax machine, or key telephone system). The FXS connector is an RJ-11 jack.

11

Image 11

Contents Models FR3060/3100 User Guide User Guide Contents Appendices Introduction and Description Preview of this Guide IntroductionRouter Management Composite Link Front Panel DescriptionVoice/Fax Channels 1 Monitor XMT/RCV Connector Power ConnectorFrame Ground GND Connector Internal Composite Link T1 DSU ConnectorVoice/Fax Channels 1 8 Connectors Channels 3 10 ConnectorsEthernet Port Technical SpecificationsCommand Port Channel ConnectorsInstallation Unpacking your MultiFRAD Safety WarningsPC or Terminal Units Cabling your MultiFRADMultiFRAD 3000-Series User Guide Software Loading and Configuration Loading your Software Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide Software Loading and Configuration MultiFRAD 3000-Series User Guide MultiFRAD Software Before You Begin Setup Menu IP Setup MultiFRAD Software IPX Setup MultiFRAD Software Spanning Tree Setup Statistics IP Statistics IPX Port Statistics STP Spanning Tree Port Statistics Snmp Statistics WAN Statistics PPP Statistics Data Port Statistics Frame Relay Statistics MultiFRAD 3000-Series User Guide WAN Port Setup Point to Point Setup Frame Relay Setup MultiFRAD 3000-Series User Guide MultiFRAD Software MultiFRAD 3000-Series User Guide Frame Relay Network Data Port Configuration Remote Configuration Modem-Based Remote Configuration Procedure Remote Configuration MultiFRAD 3000-Series User Guide Remote Configuration MultiFRAD 3000-Series User Guide Router Management MultiFRAD Telnet Server Menu Remote User Database MultiFRAD ConfigurationWEB Browser Management Router Management MultiFRAD 3000-Series User Guide Warranty, Service and Tech Support On-line Warranty Registration Limited WarrantyContacting Tech Support via E-mail Tech SupportRecording MultiFRAD Information To log on to the Multi-Tech BBS ServiceMulti-Tech BBS If you know the file name To Download a fileAbout the Internet About the Multi-Tech Fax-Back ServiceAbout CompuServe Appendices LAN Cables Appendix a Cabling Diagrams Command Port CableRS232C/V.24 * Link Cable Trunk CableCommand Port Remote Configuration CableAppendix B Regulatory Information Figure B-1. OSI Protocol Stack Appendix C Network OverviewPacket Internet Protocol IP Network AddressIP Addressing MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary MultiFRAD 3000-Series User Guide Glossary Subscriber Loop See Local loop Glossary MultiFRAD 3000-Series User Guide Index LEDs Index Telnet