Multitech MT5634ZBA-USB Command DS=n Dial Stored Telephone Number, Echo Command Mode Characters

Page 24

MT5634ZBA-USB User Guide

@Wait for quiet answer. Causes modem to wait for a ringback, then 5 seconds of silence, before processing next part of command. If silence is not detected, the modem returns a NO ANSWER code.

^Disable data calling tone transmission.

$ Detect AT&T call card “bong” tone. The character should follow the phone number and precede the user’s call card number: ATDT1028806127853500$123456789

Command: DS=n Dial Stored Telephone Number

Values:	n = 0–1
Default:	none
Description:	Dial a number previously stored in directory number y by the &Zy=x command.
	Example: ATDS=1
Command: En	Echo Command Mode Characters
Values:	n = 0 or 1
Default:	1
Description:E0	Do not echo keyboard input to the terminal.
E1	Do echo keyboard input to the terminal.
Command: Fn	Echo Online Data Characters
Values:	n = 1
Default:	1
Description:F0	Enable online data character echo. (Not supported.)
F1	Disable online data character echo (included for backward compatibility with some soft-
	ware).
Command: Hn	Hook Control
Values:	n = 0 or 1
Default:	0
Description:H0	Go on-hook (hang up).
H1	Go off-hook (make the phone line busy).
Command: In	Information Request
Values:	n = 0–5, 9, 11
Default:	None
Description:I0	Display default speed and controller firmware version.
I1	Calculate and display ROM checksum (e.g., 12AB).
I2	Check ROM and verify the checksum, displaying OK or ERROR.
I3	Display default speed and controller firmware version.
I4	Display firmware version for data pump (e.g., 94).
I5	Display the board ID: software version, hardware version, and country ID
I9	Display the country code (e.g., NA Ver. 1).
I11	Display diagnostic information for the last modem connection, such as DSP and firmware
	version, link type, line speed, serial speed, type of error correction/data compression, num-
	ber of past retrains, etc.
Command: Ln	Monitor Speaker Volume
Values:	n = 0, 1, 2, or 3
Default:	2
Description:L0	Select low volume.
L1	Select low volume.
L2	Select medium volume.
L3	Select high volume.

24

Image 24

Contents User Guide Record of Revisions TrademarksContents Index Introduction and Description Introduction Product DescriptionUniversal Serial Bus USB MT5634ZBA-USB User GuideWhat Is in Your Modem Package? Introduction and DescriptionMT5634ZBA-USB User Guide Quick Start Safety Warnings What You Will NeedWe supply You supplyAssemble the Modem Quick StartInstall the Software Connect the Modem to Your System Line ConnectionPhone Connection USB ConnectionSelect the Modem Test Your ModemFeatures Features What Can You Do with Your Modem?Data Fax Required EquipmentComputer Telephone LineConnecting to the Computer USB Connecting to the Telephone Line LineConnecting to a Telephone Set Phone ConnectionsFront Panel Front panelMT5634ZBA-USB User Guide AT Commands, S-Registers and Result Codes AT Commands AT Command Summary Command DS=n Dial Stored Telephone Number Echo Command Mode CharactersMonitor Speaker Volume Echo Online Data CharactersMonitor Speaker Mode Return Online to Data ModeResult Codes Enable/Disable Command Sr=n Set Register ValueMT5634ZBA-USB User Guide Command Vn Result Code Format Command Xn Result Code SelectionCommand Yn Long Space Disconnect Modem ResetLoad Factory Settings Command &Gn V.22bis Guard Tone ControlCommunications Mode Asynchronous Communications ModeMT5634ZBA-USB User Guide Command &Tn V.54 Test Commands Display Current SettingsCommand &Wn Store Current Configuration Select Stored Configuration for Hard ResetError Correction Mode Selection Modem Port Flow ControlData Buffer Control Break ControlInactivity Timer Command %Cn Data Compression ControlCommand %DCnAT Command Control Protocol Result CodeCommand %En Fallback and Fall Forward Control Enter Setup PasswordCommand #S=x Store Setup Password Command%%%ATCRRemote Configuration Escape SequenceRegisters S37 S38Rates K56flex Rates S42 S43S48 S89Result Codes Terse Verbose DescriptionMT5634ZBA-USB User Guide Remote Configuration Basic Procedure SetupChanging the Setup Password Remote Configuration Changing the Remote Escape CharacterMT5634ZBA-USB User Guide Troubleshooting None of the Indicators Light Modem Does Not Respond to CommandsTroubleshooting Modem Dials But Cannot ConnectModem Cannot Connect When Answering Modem Disconnects While OnlineModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same TimeAppendixes Appendix a Regulatory Compliance FCC Regulations for Telephone Line InterconnectionClass B Statement Industry CanadaCanadian Limitations Notice FAX Branding StatementEuropean Directives International Modem RestrictionsNew Zealand Telecom Warning Notice Appendix B Technical Specifications Connectors Carrier FrequenciesITU-T ITU-T V.32bis/V.32 Carrier FrequenciesDiagnostics IndicatorsDimensions WeightAppendix C Loopback Tests IntroductionFigure C-1. Local analog loopback test Test Procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Appendix C Loopback TestsFigure C-3. Local digital loopback test Test Procedure Local Digital Loopback Test V.54 LoopAppendix D Warranty, Service, and Technical Support Limited WarrantyOnline Warranty Registration ServiceTechnical Support Multi-Tech BBSTo Log on to the Multi-Tech BBS To Download a FileAbout the Multi-Tech Fax-Back Service About the InternetIndex Index MT5634ZBA-USB User Guide