Multitech MT5634ZBA-USB User Guide Command &Tn V.54 Test Commands, Display Current Settings

Page 28

MT5634ZBA-USB User Guide

Command: &Tn V.54 Test Commands

Values:

n = 0, 1, 3 or 6

Default:

None

Description:&T0

Abort. Stop any test in progress.

&T1

Local analog loopback test.

&T3

Local digital loopback test.

&T6

Remote digital loopback test.

Note: To stop a test, you must use the escape sequence (+++AT) before typing AT&T0.

Command: &V

Display Current Settings

Values:

n/a

Description:

Displays the active modem settings, including the callback security settings if callback se-

 

curity is enabled. If the setup password has been entered, it also displays the callback secu-

 

rity passwords.

Command: &Wn Store Current Configuration

Values:

n = 0

Default:

None

Description:&W0 Stores current modem settings in nonvolatile memory and causes them to be loaded at power-on or following the ATZ command instead of the factory defaults. See also the &F

 

command.

&W1 Clears user default settings from nonvolatile memory and causes the factory defaults to be

 

loaded at power-on or following the ATZ command.

Command: &Yn

Select Stored Configuration for Hard Reset

Values:

n = 0

Default:

0

Description:&Y0

Select stored configuration 0 on power-up. (For backward compatibility with some soft-

 

ware.)

&Y1

Not supported—responds ERROR.

Command: &Zy=x Store Dialing Command

Values:

y = 0–1

 

x = Dialing command

Default:

None

Description:

Stores dialing command x in memory location y. Dial the stored number using the com-

 

mand ATDS=y.

Command: \An

Select Maximum MNP Block Size

Values:

n = 0, 1, 2, or 3

Default:

3

Description:\A0

64-character maximum.

\A1

128-character maximum.

\A2

192-character maximum.

\A3

256-character maximum.

Command: \Bn

Transmit Break

Values:

n = 0–9 in 100 ms units

Default:

3

Description:

In non-error-correction mode only, sends a break signal of the specified length to a remote

 

modem. Works in conjunction with the \K command.

28

Image 28
Contents User Guide Record of Revisions TrademarksContents Index Introduction and Description Introduction Product DescriptionUniversal Serial Bus USB MT5634ZBA-USB User GuideWhat Is in Your Modem Package? Introduction and DescriptionMT5634ZBA-USB User Guide Quick Start Safety Warnings What You Will NeedWe supply You supplyAssemble the Modem Quick StartInstall the Software Connect the Modem to Your System Line ConnectionPhone Connection USB ConnectionSelect the Modem Test Your ModemFeatures What Can You Do with Your Modem? FeaturesData Fax Required EquipmentComputer Telephone LineConnecting to the Computer USB Connecting to the Telephone Line LineConnecting to a Telephone Set Phone ConnectionsFront Panel Front panelMT5634ZBA-USB User Guide AT Commands, S-Registers and Result Codes AT Commands AT Command Summary Command DS=n Dial Stored Telephone Number Echo Command Mode CharactersMonitor Speaker Volume Echo Online Data CharactersMonitor Speaker Mode Return Online to Data ModeResult Codes Enable/Disable Command Sr=n Set Register ValueMT5634ZBA-USB User Guide Command Vn Result Code Format Command Xn Result Code SelectionCommand Yn Long Space Disconnect Modem ResetLoad Factory Settings Command &Gn V.22bis Guard Tone ControlCommunications Mode Asynchronous Communications ModeMT5634ZBA-USB User Guide Command &Tn V.54 Test Commands Display Current SettingsCommand &Wn Store Current Configuration Select Stored Configuration for Hard ResetError Correction Mode Selection Modem Port Flow ControlData Buffer Control Break ControlInactivity Timer Command %Cn Data Compression ControlCommand %DCnAT Command Control Protocol Result CodeCommand %En Fallback and Fall Forward Control Enter Setup PasswordCommand #S=x Store Setup Password Command%%%ATCRRemote Configuration Escape SequenceRegisters S38 S37Rates K56flex Rates S42 S43S48 S89Result Codes Terse Verbose DescriptionMT5634ZBA-USB User Guide Remote Configuration Setup Basic ProcedureChanging the Setup Password Remote Configuration Changing the Remote Escape CharacterMT5634ZBA-USB User Guide Troubleshooting None of the Indicators Light Modem Does Not Respond to CommandsTroubleshooting Modem Dials But Cannot ConnectModem Cannot Connect When Answering Modem Disconnects While OnlineModem Doesn’t Work with Caller ID Fax and Data Software Can’t Run at the Same TimeAppendixes Appendix a Regulatory Compliance FCC Regulations for Telephone Line InterconnectionClass B Statement Industry CanadaCanadian Limitations Notice FAX Branding StatementInternational Modem Restrictions European DirectivesNew Zealand Telecom Warning Notice Appendix B Technical Specifications Connectors Carrier FrequenciesITU-T ITU-T V.32bis/V.32 Carrier FrequenciesDiagnostics IndicatorsDimensions WeightAppendix C Loopback Tests IntroductionFigure C-1. Local analog loopback test Test Procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Appendix C Loopback TestsFigure C-3. Local digital loopback test Test Procedure Local Digital Loopback Test V.54 LoopAppendix D Warranty, Service, and Technical Support Limited WarrantyOnline Warranty Registration ServiceTechnical Support Multi-Tech BBSTo Log on to the Multi-Tech BBS To Download a FileAbout the Multi-Tech Fax-Back Service About the InternetIndex Index MT5634ZBA-USB User Guide