Multitech manual MT5634ZBA-USB User Guide Command Vn Result Code Format, Result Code Options

Page 26

MT5634ZBA-USB User Guide

Command: Vn Result Code Format
Values:	n = 0 or 1
Default:	1
Description:V0	Displays result codes as digits (terse response).
V1	Displays result codes as words (verbose response).

Command: Wn	Result Code Options
Values:	n = 0, 1, or 2
Default:	2
Description:W0	CONNECT result code reports serial port speed, disables protocol result codes.
W1	CONNECT result code reports serial port speed, enables protocol result codes.
W2	CONNECT result code reports line speed, enables protocol result codes.

Command: Xn Result Code Selection
Values:	n = 0–7
Default:	4
Description:X0	Basic result codes (e.g., CONNECT); does not look for dial tone or busy signal.
X1	Extended result codes (e.g., CONNECT 46000 V42bis); does not look for dial tone or busy
	signal.
X2	Extended result codes with NO DIALTONE; does not look for busy signal.
X3	Extended result codes with BUSY; does not look for dial tone.
X4	Extended result codes with NO DIALTONE and BUSY.
X5	Extended result codes with NO DIALTONE and BUSY.
X6	Extended result codes with NO DIALTONE and BUSY.
X7	Basic result codes with NO DIALTONE and BUSY.

Command: Yn Long Space Disconnect
Values:	n = 0
Default:	0
Description:Y0	Disable sending or responding to long space break signal on disconnect.
Y1	Enable sending or responding to long space break signal on disconnect. (Not supported.)

Command: Zn	Modem Reset
Values:	n = 0 or 1
Default:	None
Description:Z0	Reset modem to profile saved by the last &W command.
Z1	Same as Z0.
Command: &Bn	V.32 Auto Retrain
Values:	n = 1
Default:	1
Description:&B0	Disable V.32 auto retrain. (Not supported.)
&B1	Enable V.32 auto retrain.
Command: &Cn	Data Carrier Detect (DCD) Control
Values:	n = 0 or 1
Default:	1
Description:&C0	Forces the DCD circuit to be always high.
&C1	DCD goes high when the remote modem’s carrier signal is detected, and goes low when
	the carrier signal is not detected.

26

Image 26

Contents User Guide Record of Revisions TrademarksContents Index Introduction and Description Universal Serial Bus USB IntroductionProduct Description MT5634ZBA-USB User GuideWhat Is in Your Modem Package? Introduction and DescriptionMT5634ZBA-USB User Guide Quick Start We supply Safety WarningsWhat You Will Need You supplyAssemble the Modem Quick StartInstall the Software Phone Connection Connect the Modem to Your SystemLine Connection USB ConnectionSelect the Modem Test Your ModemFeatures Data FeaturesWhat Can You Do with Your Modem? Computer FaxRequired Equipment Telephone LineConnecting to a Telephone Set Phone Connecting to the Computer USBConnecting to the Telephone Line Line ConnectionsFront Panel Front panelMT5634ZBA-USB User Guide AT Commands, S-Registers and Result Codes AT Commands AT Command Summary Monitor Speaker Volume Command DS=n Dial Stored Telephone NumberEcho Command Mode Characters Echo Online Data CharactersResult Codes Enable/Disable Monitor Speaker ModeReturn Online to Data Mode Command Sr=n Set Register ValueCommand Yn Long Space Disconnect MT5634ZBA-USB User Guide Command Vn Result Code FormatCommand Xn Result Code Selection Modem ResetCommunications Mode Load Factory SettingsCommand &Gn V.22bis Guard Tone Control Asynchronous Communications ModeCommand &Wn Store Current Configuration MT5634ZBA-USB User Guide Command &Tn V.54 Test CommandsDisplay Current Settings Select Stored Configuration for Hard ResetData Buffer Control Error Correction Mode SelectionModem Port Flow Control Break ControlCommand %DCnAT Command Control Inactivity TimerCommand %Cn Data Compression Control Protocol Result CodeCommand #S=x Store Setup Password Command %En Fallback and Fall Forward ControlEnter Setup Password Command%%%ATCRRemote Configuration Escape SequenceRegisters Rates K56flex Rates S37S38 S48 S42S43 S89Result Codes Terse Verbose DescriptionMT5634ZBA-USB User Guide Remote Configuration Changing the Setup Password Basic ProcedureSetup Remote Configuration Changing the Remote Escape CharacterMT5634ZBA-USB User Guide Troubleshooting None of the Indicators Light Modem Does Not Respond to CommandsTroubleshooting Modem Dials But Cannot ConnectModem Doesn’t Work with Caller ID Modem Cannot Connect When AnsweringModem Disconnects While Online Fax and Data Software Can’t Run at the Same TimeAppendixes Appendix a Regulatory Compliance FCC Regulations for Telephone Line InterconnectionClass B Statement Industry CanadaCanadian Limitations Notice FAX Branding StatementNew Zealand Telecom Warning Notice European DirectivesInternational Modem Restrictions Appendix B Technical Specifications ITU-T ConnectorsCarrier Frequencies ITU-T V.32bis/V.32 Carrier FrequenciesDimensions DiagnosticsIndicators WeightAppendix C Loopback Tests IntroductionFigure C-1. Local analog loopback test Test Procedure Local Analog Loopback Test V.54 LoopRemote Digital Loopback Test V.54 Loop Appendix C Loopback TestsFigure C-3. Local digital loopback test Test Procedure Local Digital Loopback Test V.54 LoopOnline Warranty Registration Appendix D Warranty, Service, and Technical SupportLimited Warranty ServiceTo Log on to the Multi-Tech BBS Technical SupportMulti-Tech BBS To Download a FileAbout the Multi-Tech Fax-Back Service About the InternetIndex Index MT5634ZBA-USB User Guide