Multitech MT5634ZBA-USB manual Result Codes, Terse Verbose Description

Chapter 4 - AT Commands, S-Registers and Result Codes

Result Codes

In command mode your modem can send responses called result codes to your computer. Result codes are used by communications programs and can also appear on your monitor.

Terse	Verbose	Description
0	OK	Command executed
1	CONNECT	Modem connected to line
2	RING	Ring signal detected
3	NO CARRIER	Carrier signal lost or not detected
4	ERROR	Invalid command
5 *	CONNECT 1200	Connected at 1200 bps
6	NO DIALTONE	No dial tone detected
7	BUSY	Busy signal detected
8	NO ANSWER	No answer at remote end
10*	CONNECT 2400	Connected at 2400 bps
11*	CONNECT 4800	Connected at 4800 bps
12*	CONNECT 9600	Connected at 9600 bps
13*	CONNECT 14400	Connected at 14400 bps
14*	CONNECT 19200	Connected at 19200 bps
24*	CONNECT 7200	Connected at 7200 bps
25*	CONNECT 12000	Connected at 12000 bps
26*	CONNECT 16800	Connected at 16800 bps
40*	CONNECT 300	Connected at 300 bps
55*	CONNECT 21600	Connected at 21600 bps
56*	CONNECT 24000	Connected at 24000 bps
57*	CONNECT 26400	Connected at 26400 bps
58*	CONNECT 28800	Connected at 28800 bps
59*	CONNECT 31200	Connected at 31200 bps
60*	CONNECT 33600	Connected at 33600 bps
70*	CONNECT 32000	Connected at 32000 bps, 56K rate
71*	CONNECT 34000	Connected at 34000 bps, 56K rate
72*	CONNECT 36000	Connected at 36000 bps, 56K rate
73*	CONNECT 38000	Connected at 38000 bps, 56K rate
74*	CONNECT 40000	Connected at 40000 bps, 56K rate
75*	CONNECT 42000	Connected at 42000 bps, 56K rate
76*	CONNECT 44000	Connected at 44000 bps, 56K rate
77*	CONNECT 46000	Connected at 46000 bps, 56K rate
78*	CONNECT 48000	Connected at 48000 bps, 56K rate
79*	CONNECT 50000	Connected at 50000 bps, 56K rate
80*	CONNECT 52000	Connected at 52000 bps, 56K rate
81*	CONNECT 54000	Connected at 54000 bps, 56K rate
82*	CONNECT 56000	Connected at 56000 bps, 56K rate
88	DELAYED	Delay is in effect for the dialed number
89	BLACKLISTED	Dialed number is blacklisted
90	BLACKLIST FULL	Blacklist is full
100	CONNECT 28000	Connected at 28000 bps, V.90 rate
101	CONNECT 29333	Connected at 29333 bps, V.90 rate
102	CONNECT 30666	Connected at 30666 bps, V.90 rate
103	CONNECT 33333	Connected at 33333 bps, V.90 rate
104	CONNECT 34666	Connected at 34666 bps, V.90 rate
105	CONNECT 37333	Connected at 37333 bps, V.90 rate
106	CONNECT 38666	Connected at 38666 bps, V.90 rate
107	CONNECT 41333	Connected at 41333 bps, V.90 rate
108	CONNECT 42666	Connected at 42666 bps, V.90 rate
109	CONNECT 45333	Connected at 45333 bps, V.90 rate
110	CONNECT 46666	Connected at 46666 bps, V.90 rate
111	CONNECT 49333	Connected at 49333 bps, V.90 rate
112	CONNECT 50666	Connected at 50666 bps, V.90 rate
113	CONNECT 53333	Connected at 53333 bps, V.90 rate
114	CONNECT 54666	Connected at 54666 bps, V.90 rate

*EC is added to these result codes when the extended result codes configuration option is enabled. EC is replaced by one of the following codes, depending on the type of error control connection:

V42bis —V.42 error control (LAP-M) and V.42bis data compression V42 —V.42 error control (LAP-M) only

MNP5 —MNP 4 error control and MNP 5 data compression MNP4 —MNP 4 error control only

NoEC —No error control protocol).

35