Advantech PCM-3601 user manual W1 Enable V.42 response codes, display DCE speed

Page 22

display DTE speed

W1 Enable V.42 response codes, display DCE speed

W2 Disable V.42 response codes, display DCE speed

X0 Enable basic response

codes 0-4

X1 Do not detect dial tone and busy signal

X2 Include dial tone detection response

X3 Include busy detection response

X4 Enable all response codes

Y0 Do Not send (and ignore) break signal

Y1 Send break signal for 4 seconds before disconnect

Z0 Reset modem with SCP0

Z1 Reset modem with SCP1

&C0 Turn CD signal to always on

&C1 CD on at remote carrier detected

&D0 Alone with any of following &Q0, &Q5, &Q6 then, DTR is not functional.

Alone with any of following &Q1, &Q4 then DTR drop causes the modem hang up, Auto-answer is not affected. Alone with any of following &Q2, &Q3 DTR drop causes the modem to hang up, Auto- Answer is inhibited

&D1 Alone with any of following &Q0, &Q1, &Q4, &Q5, &Q6 DTR drop is interpreted by the modem as if the asyn- chronous escape sequence had been entered. the

modem return to asynchronous command state without disconnecting. Alone with any of following &Q2, &Q3 DTR drop causes the modem to hang up. Auto- Answer is inhibited.

&D2 Alone with any of follo-wing &Q0 through %Q6 then, DTR drop causes the modem to hang up Auto- Answer is inhang.

&D3 Alone with any of following &Q0, &Q1, &Q4, &Q5, &Q6 DTR drop causes the modem to perform a softre-set as if the z command were received. The & Y setting determines which profile is loaded.

Alone with any of following &Q2, &Q3 DTR drop causes the modem to hang up Auto- Answer is inhibited.

Note: &D0 Ignore DTR & Ignore

dialing key-abort.

&F0 Restore factory default profile FDP0 (as ECDC modem)

&F1 Restore factory default profile FDP1 (as non-ECDC modem)

&G0 Disable guard tone

&G1 Disable guard tone (default for us models)

&G2 Enable 1800 Hz guard tone

&Ln Leased line dial line operation &L0 Dial-Up line operation

&L2 Leased line operation

&K0 Disable flow control &K3 RTS/CTS flow control &K4 XON/OFF flow control

Page: 21

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PCM-3601 Copyright notice Chapter Unpacking and InstallationFeature Fdsp Full -duplex speakerphone Data modem throughput up to 115.2K bpsNvram directory and stored profiles Error Correction & Data CompressionVoice/audio mode PackageUnpacking the Modem Look at the Modem CardPC/104 FaxModem Card Installing the Modem Card Setting the COM Port and Interrupt of the Modem CardSerial Port and Interrupt of the Modem Card Testing the Telephone Line Prior to Connection Communications Software ConfigurationSoftware Configuration Tips AT&P0DP Getting StartedModem Basics Modem FundamentalsData Format Communications Protocol Speeds of the ModemOn-Line Speed DCE Speed Serial Port Speed DTE SpeedError-Correction and Data Compression Ecdc Flow Control Non-Volatile Memory NvramMajor Stored Configuration Profile Major SCP Factory Default Profile FDPStored Configuration Profile SCP Active Configuration Area ACAStored Telephone Numbers STN Modem Operation and Response Codes Command State and Data StateEscape Sequence +++ Command Buffer Issuing CommandsDeleting Commands Modem AT Response Codes Dial Commands and Dial Modifiers AT CommandsPrefix, Repeat and Escape Commands Operation CommandsW1 Enable V.42 response codes, display DCE speed M0 Set modem for async operation P0 M/B ratio 39/61USA Lease Line/Dial Line command set Option Call Back Security Command Set OptionLease Line Backup Dial Line command set Option Display Dialing Number if AT&In Command supportOption Auto Dial/Redial mode Option42bis and MNP Command Set Break ControlData Compression Ecdc Operation Mode SelectionMNP Response Code Option Automatic RetrainModem Register Appendix aRegister Summary 1711h XON Character S33 255 Appendix B Result Codes+FCERROR Short Form Long Form Fax Class II Commands Fax Command Codes Fax ClassAppendix C +FDIS Installation of Modem Driver in Win 95/98 Appendix D
Top Page Image Contents