RAD Data comm ASM-60 WAN Protocol Parameters PPP Protocol Menu, Protocol Field Compression

Page 71

ASM-60Installation and Operation Manual	Appendix C IR-IP Interface Module

EIR

Used to specify the maximum amount of data, in bits, that the Frame Relay network will attempt to deliver during the measurement interval. The value of this parameter is obtained from the Frame Relay service provider.

A typical Frame Relay Protocol Parameters menu is shown in Figure C-12.

IR_IP<IR-IP>S/W Ver. 1.00 31/IR (date)

Quick Setup Management Access Advanced Setup

.....................................................................

Device identification Interface Parameters Protocol Parameters

=====================================================================

1.	Self Learn	:[ Enabled ]
2.	Maintenance Protocol	:[ ANSI T1.617 ANNEX D ]
3.	DLCI (0-None)	:0..
4.	CIR	:0
5.	EIR	:64000...

Press one of the numbers to select or ESC:

Figure C-12. Frame Relay Protocol Parameters Menu

WAN Protocol Parameters – PPP Protocol Menu

The PPP Protocol Parameters menu is used to configure the parameters PPP WAN for protocol (the WAN protocol is selected by means of the (the WAN protocol is selected by means of the Quick Setup Menu) in Figure C-6.

To access the Protocol Parameters menu:

•From the Advanced Setup menu, type 3.

Header and Control Field Compression

Used to control the use of header and control field compression type according to RFC 1661. It is strongly recommended that this compression be used for troubleshooting only.

Protocol Field Compression

Used to control the use of protocol field compression type according to RFC 1661. It is strongly recommended that this compression be used for troubleshooting only.

Authentication Protocol

Used to select the authentication protocol used by an IP router configured as host to validate incoming connections.

Advanced Setup Menu

C-17

Image 71

Contents ASM-60 Page International Headquarters RAD Data Communications Inc ASM-60Limited Warranty Please observe the following precautions General Safety InstructionsConnection of DC Mains General Safety PracticesConnection of AC Mains Connection of Data and Telecommunications Cables Ports Safety StatusElectromagnetic Compatibility EMC Canadian Emission Requirements Page Supplementary Information SafetyManufacturers Name Manufacturers Address Product NamePage Connecting the Power Installing ASM-60Setting the Internal Switches Connecting the InterfacesSelecting the Data Rate Configuring ASM-60Operating ASM-60 Normal IndicationsContents Diagnostics List of Figures Table of Contents Application Chapter IntroductionOverview VersionsFeatures D View of ASM-60 Physical DescriptionFunctional Description ASM-60 Block DiagramInterface 24/RS-232 Type Technical SpecificationsRange Data RateFuse 250A, slow-blow AC Voltage 100 to 240 VAC ±10%, 50 to 60 Hz, 6W ProtectionTransformers to the transmit and receive lines Site Requirements and Prerequisites Chapter Installation and SetupInstallation and Setup Package ContentsClosing the ASM-60 Case Connecting the LineOpening the ASM-60 Case To connect the Hssi interface Connecting the DTEHssi Interface Connector Pinout To connect the AC power Installation and Setup Name Function Front Panel IndicatorsLED Indicators Chapter OperationTurning Off ASM-60 ASM-60 Indicator StatusTurning On ASM-60 Normal OperationPreparing Terminal Control Port Interface CharacteristicsChapter Management from a Terminal Preparing for the Control SessionTo choose an option Navigating the Management MenusInitiating a Control Session To initiate a control sessionTerminal Management Menus Starting the Control SessionMain Menu To display the Configuration menuDisplaying the ASM-60 System Information To access the Display menuTo display the ASM-60 status Displaying the ASM-60 StatusTo reset ASM-60 Resetting ASM-60Resetting ASM-60 Alarms Chapter DiagnosticsError Detection Power-Up Self-TestWorking with the Log File To access the log fileNumber Terminal Message Description Severity Displaying the Vdsl Performance DiagnosticsASM-60 Alarms To display the Vdsl diagnosticsASM-60 Performance Monitoring Parameters After the ASM-60 power-upTo run the LEDs test Running the Diagnostic TestsRunning the LEDs Test Running the Diagnostic Tests Appendix a IR-ETH Interface Module IR-ETH Connector OptionsAppendix a IR-ETH Interface Module ProtocolSection Name Description Default Number Setting Installation and OperationDIP Switch Settings Table A-2. DIP Switch SettingsDescription Location Color Name LED IndicatorsConnecting to LAN Table A-3. IR-ETH Bridge LED IndicatorsIntroduction IR-ETH/QH ConnectorAppendix B IR-ETH/QH Interface Module Protocol Point-to-point Data Rate Kbps to 45 Mbps Table B-1 RJ-45 Connector PinoutPin Signal Function Section Name Description Possible Settings Factory Setting Setting the DIP SwitchTable B-2. DIP Switch Settings Table B-3. IR-ETH/QH LED IndicatorsConnecting the LAN Overview Appendix C IR-IP Interface ModuleProtocols Delay FrameConnector 10BaseT UTP Shielded RJ-45 Standard Conforms to Ieee 802.3/Ethernet Data Rate MbpsTable C-3 RJ-45 Pinout IR-IP DIP SwitchIR-IP LEDs Table C-1. IR-IP LEDs FunctionsIntroduction Accessing the IR-IP Management SubsystemIR-IP Management Subsystem, General To perform the preliminary configuration procedure Performing Preliminary ConfigurationDefault IP Communication Parameters Outline of Preliminary ConfigurationIP Learning Mechanism Connecting the Telnet HostPreliminary Telnet Host Configuration Assigning the Router LAN Interface AddressAssigning a LAN IP Address to a New IR-IP To view and edit the ARP table contentsTo configure the IP router LAN address IP learning process is not successful Changing the LAN IP Address of a Configured IR-IPWhat to Do If No ping replies from IR-IPStarting a Management Utility General Operating ProceduresIR-IP Management Utility Menu Structure of Management Utility Quick Setup MenuTo access the Quick Setup menu WAN IP Address Default GatewayLAN IP Address LAN IP MaskParameters Read Protocol from DIP SwitchesOperation with Default Gateway ProtocolTo access the Management Access menu Management Access MenuTelnet Password Telnet Inactivity Timeout Device Identification Menu Advanced Setup Menu To access the Advanced Setup menu To access the Device Identification menuInterface Parameters Menu WAN Throttle Aging TimeoutMaintenance Protocol WAN Protocol Parameters Frame Relay Protocol MenuProtocol Field Compression Authentication ProtocolWAN Protocol Parameters PPP Protocol Menu Header and Control Field CompressionUser Name To Send Password To SendPassword To Accept Security Host/GuestMulticast Forwarding To access the Multicast IP menuMulticast IP Menu Static Groups To access the Static Groups menuTo access the Device Control menu Device Control MenuFile Name Total TimeoutNew Software Download Menu Server IP AddressReset LAN View Error Log ScreenResets Menu Reset DeviceView Menu Configuration and ConnectionReset WAN Multicast Groups Table Screen To access the ARP Tables screenTo access the Multicast Groups Table screen ARP TablesStatistics Screen To access the Statistics menuTo access the Diagnostic Tools menu Diagnostic Tool Ping Terminal MenuTo ping a host Using the Ping FunctionDesired positions, and then turn ASM-60 on again Erasing User’s ConfigurationTo erase the user’s configuration Erasing IR-IP SoftwareCase, it is recommended to turn ASM-60 off and then back on Erasing Application SoftwareDownloading New Software To erase the application softwareAppendix C IR-IP Interface Module Erasing IR-IP Software Excellent Good Fair Poor Very Poor Customer Response FormPage Error Report Page Page International Headquarters

Related manuals

Manual 74 pages 54.1 Kb