RAD Data comm ASM-60 operation manual Erasing User’s Configuration, Erasing IR-IP Software

Page 82

Appendix C IR-IP Interface ModuleASM-60Installation and Operation Manual

 

C.13

Erasing User’s Configuration

 

The user-defined configuration parameters are stored in the IP router card flash

 

memory. After the user-defined configuration parameters are erased, the IP router

 

card automatically loads the default parameters.

 

You may want to erase the current configuration parameters:

 

1.

Before IR-IP is prepared for operation in a new application.

 

2.

When you cannot configure IR-IP because its current LAN-interface IP address

 

 

and/or the Telnet password, are not known.

 

To erase the user’s configuration:

 

1.

Turn ASM-60 off.

 

2.

Set all the four sections of the IR-IP DIP switch to ON.

 

3.

Turn ASM-60 on and monitor the ERR indicator: it must turn on and start

 

 

blinking.

 

4.

While the ERR indicator is blinking (within 15 seconds), set sections 1 and 2 of

 

 

the DIP switch to OFF.

 

 

 

When the ERR indicator stops blinking and lights steadily, the IP router

 

 

 

configuration becomes erased.

Note

 

 

 

If you do not set sections 1 and 2 to OFF within 15 seconds of power-up, the IP

 

 

router card ignores the setting of all the four sections to ON and starts normal

 

operation. In this case, it is recommended to turn ASM-60 off and then back on.

 

To abort the whole operation, turn ASM-60 off, return all the four-switch section to

 

the desired positions, and then turn ASM-60 on again.

 

 

 

 

5.

Turn ASM-60 off, and the return all the four sections of the DIP switch to the

 

 

desired positions.

C.14 Erasing IR-IP Software

You may erase the IR-IP application software, without erasing the user-defined parameters.

After the application software is erased, IR-IP starts its TFTP server application, and waits for the downloading of software by a TFTP client connected to its LAN interface. The procedure to be used to download the application software in this case is also described below.

You may want to erase the application software if the downloading of new software using the Device Control menu (see Figure C-16)fails, and IR-IP does not function properly.

C-28 Erasing IR-IP Software

Page 81 Page 83
Image 82
Page 81 Page 83
Contents ASM-60 Page ASM-60 International Headquarters RAD Data Communications IncLimited Warranty General Safety Instructions Please observe the following precautionsConnection of AC Mains General Safety PracticesConnection of DC Mains Ports Safety Status Connection of Data and Telecommunications CablesElectromagnetic Compatibility EMC Canadian Emission Requirements Page Product Name SafetyManufacturers Name Manufacturers Address Supplementary InformationPage Connecting the Interfaces Installing ASM-60Setting the Internal Switches Connecting the PowerNormal Indications Configuring ASM-60Operating ASM-60 Selecting the Data RateContents Diagnostics List of Figures Table of Contents Versions Chapter IntroductionOverview ApplicationFeatures Physical Description D View of ASM-60ASM-60 Block Diagram Functional DescriptionData Rate Technical SpecificationsRange Interface 24/RS-232 TypeTransformers to the transmit and receive lines AC Voltage 100 to 240 VAC ±10%, 50 to 60 Hz, 6W ProtectionFuse 250A, slow-blow Chapter Installation and Setup Site Requirements and PrerequisitesPackage Contents Installation and SetupOpening the ASM-60 Case Connecting the LineClosing the ASM-60 Case Hssi Interface Connector Pinout Connecting the DTETo connect the Hssi interface To connect the AC power Installation and Setup Chapter Operation Front Panel IndicatorsLED Indicators Name FunctionNormal Operation ASM-60 Indicator StatusTurning On ASM-60 Turning Off ASM-60Preparing for the Control Session Control Port Interface CharacteristicsChapter Management from a Terminal Preparing TerminalTo initiate a control session Navigating the Management MenusInitiating a Control Session To choose an optionStarting the Control Session Terminal Management MenusTo display the Configuration menu Main MenuTo access the Display menu Displaying the ASM-60 System InformationDisplaying the ASM-60 Status To display the ASM-60 statusResetting ASM-60 To reset ASM-60Resetting ASM-60 Power-Up Self-Test Chapter DiagnosticsError Detection AlarmsTo access the log file Working with the Log FileTo display the Vdsl diagnostics Displaying the Vdsl Performance DiagnosticsASM-60 Alarms Number Terminal Message Description SeverityAfter the ASM-60 power-up ASM-60 Performance Monitoring ParametersRunning the LEDs Test Running the Diagnostic TestsTo run the LEDs test Running the Diagnostic Tests IR-ETH Connector Options Appendix a IR-ETH Interface ModuleProtocol Appendix a IR-ETH Interface ModuleTable A-2. DIP Switch Settings Installation and OperationDIP Switch Settings Section Name Description Default Number SettingTable A-3. IR-ETH Bridge LED Indicators LED IndicatorsConnecting to LAN Description Location Color NameAppendix B IR-ETH/QH Interface Module IR-ETH/QH ConnectorIntroduction Pin Signal Function Table B-1 RJ-45 Connector PinoutProtocol Point-to-point Data Rate Kbps to 45 Mbps Table B-3. IR-ETH/QH LED Indicators Setting the DIP SwitchTable B-2. DIP Switch Settings Section Name Description Possible Settings Factory SettingConnecting the LAN Appendix C IR-IP Interface Module OverviewStandard Conforms to Ieee 802.3/Ethernet Data Rate Mbps Delay FrameConnector 10BaseT UTP Shielded RJ-45 ProtocolsTable C-1. IR-IP LEDs Functions IR-IP DIP SwitchIR-IP LEDs Table C-3 RJ-45 PinoutIR-IP Management Subsystem, General Accessing the IR-IP Management SubsystemIntroduction Outline of Preliminary Configuration Performing Preliminary ConfigurationDefault IP Communication Parameters To perform the preliminary configuration procedureAssigning the Router LAN Interface Address Connecting the Telnet HostPreliminary Telnet Host Configuration IP Learning MechanismTo configure the IP router LAN address To view and edit the ARP table contentsAssigning a LAN IP Address to a New IR-IP No ping replies from IR-IP Changing the LAN IP Address of a Configured IR-IPWhat to Do If IP learning process is not successfulIR-IP Management Utility General Operating ProceduresStarting a Management Utility To access the Quick Setup menu Quick Setup MenuMenu Structure of Management Utility LAN IP Mask Default GatewayLAN IP Address WAN IP AddressProtocol Read Protocol from DIP SwitchesOperation with Default Gateway ParametersTelnet Inactivity Timeout Management Access MenuTelnet Password To access the Management Access menuTo access the Device Identification menu Advanced Setup MenuTo access the Advanced Setup menu Device Identification MenuInterface Parameters Menu WAN Protocol Parameters Frame Relay Protocol Menu Aging TimeoutMaintenance Protocol WAN ThrottleHeader and Control Field Compression Authentication ProtocolWAN Protocol Parameters PPP Protocol Menu Protocol Field CompressionSecurity Host/Guest Password To SendPassword To Accept User Name To SendMulticast IP Menu To access the Multicast IP menuMulticast Forwarding Device Control Menu To access the Static Groups menuTo access the Device Control menu Static GroupsServer IP Address Total TimeoutNew Software Download Menu File NameReset Device View Error Log ScreenResets Menu Reset LANReset WAN Configuration and ConnectionView Menu ARP Tables To access the ARP Tables screenTo access the Multicast Groups Table screen Multicast Groups Table ScreenTo access the Statistics menu Statistics ScreenDiagnostic Tool Ping Terminal Menu To access the Diagnostic Tools menuUsing the Ping Function To ping a hostErasing IR-IP Software Erasing User’s ConfigurationTo erase the user’s configuration Desired positions, and then turn ASM-60 on againTo erase the application software Erasing Application SoftwareDownloading New Software Case, it is recommended to turn ASM-60 off and then back onAppendix C IR-IP Interface Module Erasing IR-IP Software Customer Response Form Excellent Good Fair Poor Very PoorPage Error Report Page Page International Headquarters
Related manuals
Manual 74 pages 54.1 Kb

ASM-60 specifications

The RAD Data Communications ASM-60 is a highly advanced access and service management platform designed to streamline the deployment and management of various telecommunications services. It is particularly well-suited for carrier-grade applications, offering a robust solution that meets the demands of modern communication networks. The ASM-60 integrates multiple functionalities, ensuring that service providers can efficiently manage their networks and deliver high-quality services to their customers.

One of the standout features of the ASM-60 is its versatility. It supports a wide range of technologies, including Ethernet, TDM, and IP-based services. This adaptability allows service providers to seamlessly integrate legacy systems with newer technologies, ensuring a smooth transition as networks evolve. The platform is equipped to handle both synchronous and asynchronous services, catering to diverse customer needs while maximizing operational efficiency.

Reliability is paramount in telecommunications, and the ASM-60 excels in this regard. It boasts built-in redundancy features, ensuring continuous operation even in the event of a hardware failure. The platform is designed with hot-swappable components, allowing for maintenance and upgrades without disrupting service. This characteristic makes it an ideal choice for mission-critical applications that require uninterrupted service delivery.

In terms of scalability, the ASM-60 offers a comprehensive solution for growing networks. With its modular design, service providers can easily expand their infrastructure as demand increases. This scalability ensures that organizations can effectively respond to changing market conditions and customer requirements, facilitating long-term growth.

Another significant aspect of the ASM-60 is its advanced management capabilities. The platform is equipped with a user-friendly interface that simplifies configuration, monitoring, and troubleshooting tasks. It supports various management protocols, including SNMP and Command Line Interface (CLI), enabling seamless integration with existing network management systems.

Security is also a critical consideration in the design of the ASM-60. It features multiple layers of security, including encryption and authentication protocols, to safeguard sensitive data. This commitment to security helps service providers maintain the integrity and confidentiality of their customers’ information.

In conclusion, the RAD Data Communications ASM-60 is a powerful access and service management platform that meets the diverse needs of modern telecommunications networks. With its versatility, reliability, scalability, advanced management capabilities, and robust security features, the ASM-60 is an ideal choice for service providers looking to enhance their operational efficiency and deliver top-notch services to their customers.
Top Page Image Contents