Promise Technology 150TX2 user manual Rebuilding a Mirrored Array

Page 40

FastTrak S150 TX2plus User Manual

Rebuilding a Mirrored Array

The Rebuild Array (5) Menu option can be used to recover from an error in a mirrored disk array. You will receive an error message when booting your system from the FastTrak BIOS.

Important

Drives MUST be replaced if they contain any physical errors.

Follow these steps before using the Rebuild Array menu option:

1.On bootup, the FastTrak S150 TX2plus Startup BIOS will display an error message identifying which drive has failed.

2.Press Ctrl-F to enter FastBuild Main Menu.

3.Select submenu Define Array (3).

4.Select the failed array and identify the Channel and ID of the failed drive.

5.Power off and physically remove the failed drive.

6.Replace the drive with an identical model.

7.Reboot the system and enter the FastBuild Main Menu.

8.Select the Rebuild Array (5) option. The following screen will appear.

FastBuild (tm) Utility 2.xx (c) 2002-2005 Promise Technology, Inc.

[ Rebuild Array Menu ]

Array No

RAID Mode

Total Drv

Capacity(MB)

Status

Array 1

Stripe

2

160048

Functional

Array 2

Mirror

2

80024

Critical

Array 3

——

——

——

——

Array 4

——

——

——

——

 

 

[ Keys Available ]

 

[] Up [] Down

[ESC] Exit

[Enter] Select

 

 

9.Highlight the array whose Status is Critical.

10.Press Enter. The following screen will then appear (see next page).

36

Image 40
Contents Fasttrak S150 TX2PLUS Trademarks CopyrightImportant Data Protection Information Contents Page Introduction FastTrak S150 TX2plusPromise Array Management Utility PAM Key Features and Benefits Features BenefitsCompatibility Installation Unpacking Your FastTrak CardInstalling the FastTrak Card Insert the FastTrak card into an open PCI slotInstalling the Hard Drives FastTrak S150 TX2plus card Creating Your Disk Array Creating a Performance Array Creating a Security Array with New Drives Page Creating a Security Array with an Existing Data Drive Seagate S380023AS Installation Creating a Security Array with Quick Initialization Installation Page Using FastBuild Configuration Utility Viewing FastTrak S150 TX2plus Bios ScreenNavigating the FastBuild Setup Menu Using the Main MenuOptimize Array for Creating Arrays AutomaticallyPerformance Security Security and PerformanceUsing a Hot Spare Drive Viewing Drive Assignments Creating Multiple ArraysManually Creating an Array Selecting Array Type Selecting Stripe BlockGigabyte Boundary Assigning Drives to Array Creating a Striped ArrayCreating a Mirrored Array Using New Drives Adding Fault Tolerance to an Existing Drive Drive Model Capacity MB Page How FastTrak S150 TX2plus Orders Arrays Creating a Hot Spare Drive for Mirrored ArraysHow FastTrak S150 TX2plus Saves Array Information Deleting an Array Array Stripe 160048 Rebuilding a Mirrored Array 80024 Page Installing Software Drivers Procedure NumberWindows XP Installation Existing Windows XP Installation Confirming Windows XP Driver InstallationNew Windows 2000 Installation Existing Windows 2000 Installation Confirming Windows 2000 Driver InstallationNew Windows ME Installation Existing Windows ME Installation Confirming Windows ME Driver InstallationNew Windows NT4.0 Installation Existing Windows NT4.0 Installation Removing Driver from Windows NT4.0New Windows 98 Installation Existing Windows 98 Installation Confirming Windows 98 Driver InstallationPage About Adapter Bios FastBuild Auto Menu SetupAbout FastTrak S150 TX2plus Reserve SectorRAID Level Performance Fault Capacity No. Tolerance Drives Disk Array TermsDisk Array Description Disk Array MemberAbout RAID Levels Striping RAIDMirroring RAID Data Mirror Disk DrivesDisk Array Concepts Striping / Mirroring RAID 0+1 Motherboard Issues Configuring PCI IRQ resourcesIntermittent data problems Freeing additional IRQ resourcesSystem Cmos Issues Using an Onboard IDE Card with FastTrak S150 TX2plusDrive-Related Errors Critical Array Status Error Reported during BootDrive cannot be formed into an array System Cmos displays C or D drive failure during StartupUnable to Partition or Format Array Cannot Rebuild Mirrored RAID 1 Array Operating System-Related Issues Promise Windows driver does not appear in Device ManagerTroubleshooting & Tips Performance Tips Optimize Array for PerformanceChange Setting of PCI Bus Utilization Page Appendix a Frequently Asked Questions Pre-InstallationRAID 1 Mirror RAID 0 StripeRAID 0+1 Stripe + Mirror Drive Issues Page Installation Issues Post-InstallationPage USA Tech Support Center Technical Support ServicesEuropean Tech Support Pacific Rim Sales Office China OfficeLimited Warranty Disclaimer of other warrantiesYour Responsibilities Returning Product for Repair