Promise Technology 150TX2 user manual New Windows NT4.0 Installation

Page 50

FastTrak S150 TX2plus User Manual

New Windows NT4.0 Installation

The following details the installation of the FastTrak TX2plus drivers while installing Windows NT4.0.

1.Start the system installation by booting from the Windows NT disk:

Floppy install: boot the system with the Windows NT installation diskettes.

CD-ROM disk install: boot from the CD-ROM disk and press F6 when the message “Setup is inspecting your computer’s hardware configuration…” appears.

2.When the Windows NT Setup window is generated, press S to Specify an Additional Device(s).

3.Press O to select Other then press Enter.

4.Insert the FastTrak TX2plus driver diskette into drive A: and press Enter.

5.Choose WinNT Promise FastTrak TX4000/S150 TX Series Controller from the list that appears on screen then press Enter.

6.The Windows NT Setup screen will appear again saying “Setup will load support for the following mass storage devices:” The list will include WinNT Promise FastTrak TX2plus Controller.

NOTE: If there are any additional devices to be installed, specify them now. When all devices are specified, continue to the next step.

7.From the Windows NT Setup screen, press Enter. Setup will now load all device files and then continue the Windows NT installation.

8.After a successful installation, the SCSI Adapter Setup box will show that the “WinNT Promise FastTrak TX4000/S150 TX Series Controller” driver has been installed.

46

Image 50
Contents Fasttrak S150 TX2PLUS Important Data Protection Information CopyrightTrademarks Contents Page Introduction FastTrak S150 TX2plusPromise Array Management Utility PAM Key Features and Benefits Features BenefitsCompatibility Installation Unpacking Your FastTrak CardInstalling the FastTrak Card Insert the FastTrak card into an open PCI slotInstalling the Hard Drives FastTrak S150 TX2plus card Creating Your Disk Array Creating a Performance Array Creating a Security Array with New Drives Page Creating a Security Array with an Existing Data Drive Seagate S380023AS Installation Creating a Security Array with Quick Initialization Installation Page Using FastBuild Configuration Utility Viewing FastTrak S150 TX2plus Bios ScreenNavigating the FastBuild Setup Menu Using the Main MenuPerformance Creating Arrays AutomaticallyOptimize Array for Security Security and PerformanceUsing a Hot Spare Drive Viewing Drive Assignments Creating Multiple ArraysManually Creating an Array Selecting Array Type Selecting Stripe BlockGigabyte Boundary Assigning Drives to Array Creating a Striped ArrayCreating a Mirrored Array Using New Drives Adding Fault Tolerance to an Existing Drive Drive Model Capacity MB Page How FastTrak S150 TX2plus Saves Array Information Creating a Hot Spare Drive for Mirrored ArraysHow FastTrak S150 TX2plus Orders Arrays Deleting an Array Array Stripe 160048 Rebuilding a Mirrored Array 80024 Page Installing Software Drivers Procedure NumberWindows XP Installation Existing Windows XP Installation Confirming Windows XP Driver InstallationNew Windows 2000 Installation Existing Windows 2000 Installation Confirming Windows 2000 Driver InstallationNew Windows ME Installation Existing Windows ME Installation Confirming Windows ME Driver InstallationNew Windows NT4.0 Installation Existing Windows NT4.0 Installation Removing Driver from Windows NT4.0New Windows 98 Installation Existing Windows 98 Installation Confirming Windows 98 Driver InstallationPage About FastTrak S150 TX2plus About Adapter BiosFastBuild Auto Menu Setup Reserve SectorDisk Array Description RAID Level Performance Fault Capacity No. Tolerance DrivesDisk Array Terms Disk Array MemberAbout RAID Levels Striping RAIDMirroring RAID Data Mirror Disk DrivesDisk Array Concepts Striping / Mirroring RAID 0+1 Intermittent data problems Motherboard IssuesConfiguring PCI IRQ resources Freeing additional IRQ resourcesSystem Cmos Issues Using an Onboard IDE Card with FastTrak S150 TX2plusDrive cannot be formed into an array Drive-Related ErrorsCritical Array Status Error Reported during Boot System Cmos displays C or D drive failure during StartupUnable to Partition or Format Array Cannot Rebuild Mirrored RAID 1 Array Operating System-Related Issues Promise Windows driver does not appear in Device ManagerTroubleshooting & Tips Performance Tips Optimize Array for PerformanceChange Setting of PCI Bus Utilization Page Appendix a Frequently Asked Questions Pre-InstallationRAID 0+1 Stripe + Mirror RAID 0 StripeRAID 1 Mirror Drive Issues Page Installation Issues Post-InstallationPage European Tech Support Technical Support ServicesUSA Tech Support Center Pacific Rim Sales Office China OfficeLimited Warranty Disclaimer of other warrantiesYour Responsibilities Returning Product for Repair