Promise Technology 150TX2 user manual System Cmos Issues

Page 62

FastTrak S150 TX2plus User Manual

System CMOS Issues

Set Motherboard CMOS Boot sequence to boot to FastTrak S150 TX2plus

On some Motherboard BIOS, it is necessary to set the Boot sequence to SCSI, A:, C: since the Promise card is identified as a SCSI card.

Motherboard CMOS displays C: or D: drive failure during startup

See the Drive-Related Errors section.

Using an Onboard IDE Card with FastTrak S150 TX2plus

If an onboard IDE controller is installed with hard disks, enable support in the Motherboard Standard CMOS Setup for the drives. Note that the onboard IDE hard drives will then be the bootable hard disk unless the system BIOS has a boot sequence setting with the option to specify booting to a different device.

58

Image 62

Contents Fasttrak S150 TX2PLUS Important Data Protection Information CopyrightTrademarks Contents Page Introduction FastTrak S150 TX2plusPromise Array Management Utility PAM Key Features and Benefits Features BenefitsCompatibility Installation Unpacking Your FastTrak CardInstalling the FastTrak Card Insert the FastTrak card into an open PCI slotInstalling the Hard Drives FastTrak S150 TX2plus card Creating Your Disk Array Creating a Performance Array Creating a Security Array with New Drives Page Creating a Security Array with an Existing Data Drive Seagate S380023AS Installation Creating a Security Array with Quick Initialization Installation Page Using FastBuild Configuration Utility Viewing FastTrak S150 TX2plus Bios ScreenNavigating the FastBuild Setup Menu Using the Main MenuPerformance Creating Arrays AutomaticallyOptimize Array for Security Security and PerformanceUsing a Hot Spare Drive Viewing Drive Assignments Creating Multiple ArraysManually Creating an Array Selecting Array Type Selecting Stripe BlockGigabyte Boundary Assigning Drives to Array Creating a Striped ArrayCreating a Mirrored Array Using New Drives Adding Fault Tolerance to an Existing Drive Drive Model Capacity MB Page How FastTrak S150 TX2plus Saves Array Information Creating a Hot Spare Drive for Mirrored ArraysHow FastTrak S150 TX2plus Orders Arrays Deleting an Array Array Stripe 160048 Rebuilding a Mirrored Array 80024 Page Installing Software Drivers Procedure NumberWindows XP Installation Existing Windows XP Installation Confirming Windows XP Driver InstallationNew Windows 2000 Installation Existing Windows 2000 Installation Confirming Windows 2000 Driver InstallationNew Windows ME Installation Existing Windows ME Installation Confirming Windows ME Driver InstallationNew Windows NT4.0 Installation Existing Windows NT4.0 Installation Removing Driver from Windows NT4.0New Windows 98 Installation Existing Windows 98 Installation Confirming Windows 98 Driver InstallationPage About FastTrak S150 TX2plus About Adapter BiosFastBuild Auto Menu Setup Reserve SectorDisk Array Description RAID Level Performance Fault Capacity No. Tolerance DrivesDisk Array Terms Disk Array MemberAbout RAID Levels Striping RAIDMirroring RAID Data Mirror Disk DrivesDisk Array Concepts Striping / Mirroring RAID 0+1 Intermittent data problems Motherboard IssuesConfiguring PCI IRQ resources Freeing additional IRQ resourcesSystem Cmos Issues Using an Onboard IDE Card with FastTrak S150 TX2plusDrive cannot be formed into an array Drive-Related ErrorsCritical Array Status Error Reported during Boot System Cmos displays C or D drive failure during StartupUnable to Partition or Format Array Cannot Rebuild Mirrored RAID 1 Array Operating System-Related Issues Promise Windows driver does not appear in Device ManagerTroubleshooting & Tips Performance Tips Optimize Array for PerformanceChange Setting of PCI Bus Utilization Page Appendix a Frequently Asked Questions Pre-InstallationRAID 0+1 Stripe + Mirror RAID 0 StripeRAID 1 Mirror Drive Issues Page Installation Issues Post-InstallationPage European Tech Support Technical Support ServicesUSA Tech Support Center Pacific Rim Sales Office China OfficeLimited Warranty Disclaimer of other warrantiesYour Responsibilities Returning Product for Repair