| Page 33 of 51 |
Appendix D.2. Metasys DC9100 Memory Map
Note: The DC9100 is not currently supported by the FieldServer MetasysN2 Driver. The information below is for interest and future use only.
PAGE 0
Item | Item |
| Signal Condition | Read/Write | Johnson | Description |
|
DEC | HEX |
| Tag |
| |||
|
|
|
|
| |||
0 |
| 0 | Byte | Read | MODL | Device model. Value always either 2 or | |
| 12 |
| |||||
|
|
|
|
|
|
| |
1 |
| 1 | FP | Read | INP1 | Analog input 1 | |
2 |
| 2 | FP | Read | INP2 | Analog input 2 | |
3 |
| 3 | FP | Read | INP3 | Analog input 3 | |
4 |
| 4 | FP | Read | INP4 | Analog input 4 | |
5 |
| 5 | FP | Read | INP5 | Analog input 5 | |
6 |
| 6 | FP | Read | INP6 | Analog input 6 | |
7 |
| 7 | FP | Read | INP7 | Analog input 7 | |
8 |
| 8 | FP | Read | INP8 | Analog input 8 | |
9 |
| 9 | FP | Read | NCM1 | Numeric calculation modul result | |
10 | A |
| FP | Read | NCM2 | Numeric calculation modul result | |
11 | B |
| FP | Read | NCM3 | Numeric calculation modul result | |
12 | C |
| FP | Read | NMC4 | Numeric calculation modul result | |
13 | D |
| FP | Write | REC1 | Remote constant 1 | |
14 | E |
| FP | Write | REC2 | Remote constant 2 | |
15 | F |
| FP | Write | REC3 | Remote constant 3 | |
16 |
| 10 | FP | Write | REC4 | Remote constant 4 | |
17 |
| 11 | FP | Write | OUT1 | Control output 1 | |
18 |
| 12 | FP | Write | OUT2 | Control output 2 | |
19 |
| 13 | FP | Write | OUT3 | Control output 3 | |
20 |
| 14 | FP | Write | OUT4 | Control output 4 | |
21 |
| 15 | FP | Write | OUT5 | Control output 5 | |
22 |
| 16 | FP | Write | OUT6 | Control output 6 | |
23 |
| 17 | FP | Write | OUT7 | Control output 7 | |
24 |
| 18 | FP | Write | OUT8 | Control output 8 | |
25 |
| 19 | FP | Write | WSP1 | Working setpoint 1 | |
26 | 1A |
| FP | Write | WSP2 | Working setpoint 2 | |
27 | 1B |
| FP | Write | WSP3 | Working setpoint 3 | |
28 | 1C |
| FP | Write | WSP4 | Working setpoint 4 | |
29 | 1D |
| FP | Write | WSP5 | Working setpoint 5 | |
30 | 1E |
| FP | Write | WSP6 | Working setpoint 6 | |
31 | 1F |
| FP | Write | WSP7 | Working setpoint 7 | |
32 |
| 20 | FP | Write | WSP8 | Working setpoint 8 | |
33 |
| 21 | Word | Read | STW1 | Status word 1 | |
34 |
| 22 | Word | Read | STW2 | Status word 2 | |
35 |
| 23 | Word | Read | STW3 | Status word 3 | |
36 |
| 24 | Word | Read | STW4 | Status word 4 | |
37 |
| 25 | Word | Read | STW5 | Status word 5 | |
38 |
| 26 | Word | Read | STW6 | Status word 6 | |
39 |
| 27 | Word | Read | STW7 | Status word 7 | |
40 |
| 28 | Word | Read | STW8 | Status word 8 | |
41 |
| 29 | Word | Write | DOUT | Logic output DDC control | |
42 | 2A |
| Byte | Write | CHLD | Hold mode control | |
43 | 2B |
| Byte | Write | COMP | Supervisory mode control | |
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com Tel: (408)