HotBrick VPN 800/2 manual Settings Load Balance, Statistics, Interface, Buttons

Page 25

 

HotBrick Network Solutions

Settings – Load Balance

 

 

Load Balance

Enable – Use this to enable your Load Balance settings. Unless this is

Configuration

checked, the other settings on this screen have no effect.

 

Balance Type – Select the desired option:

 

• Bytes rx+tx – Traffic is measured by Bytes.

 

• Packets rx+tx – Traffic is measured by Packets.

 

• Sessions established – Traffic is measured by Sessions.

 

• IP Address – Traffic is measured by IP Address.

 

Loading Share on WAN 1 – Enter the percentage (%) of traffic to be sent

 

over WAN 1. If one WAN port connection has greater bandwidth than the

 

other, the one with the greater bandwidth should be given a higher percentage

 

of traffic than the other.

 

Click the "Update" button to save your changes.

 

 

NAT

This section displays the current data about WAN 1 and WAN 2. You can use this

Statistics

information to help you "fine-tune" the settings above.

Interface

This section displays cumulative statistics.

Statistics

Use the "Restart Counters" button to restart these counters when required.

 

 

 

Buttons

Update – Save the settings on this screen.

 

Refresh – Update the data on screen.

 

Restart Counters – Restart the counters used in the "Interface Statistics"

 

section.

Page 21

Image 25
Contents Dual WAN Firewall Router VPN 800 User’s Guide Page Table of Contents Existing Dhcp Server ………………………………………………………………………………...68 Advanced LAN Configuration ………………………………………………………………...68Introduction Internet FeaturesThis gives twice the bandwidth of a single modem PPPoE Session Management Port Switching Hub Other FeaturesPhysical Details Package ContentsLED Action Condition AC power socket Default SettingsRear Panel VPN 800/2 Firewall Router Page Procedure Basic SetupConfiguring the VPN 800/2 Firewall Router for your LAN OverviewNo Response? LAN IP Configuration Settings LAN & DhcpLAN Any IP Setup ConfigurationDhcp Server Dhcp IP AddressHotBrick Network Solutions Connection Mode Settings Primary SetupType ConnectionAddress Info PPPoE / PptpTCP/IP Settings Configure PCs on your LANInternet Access OverviewMacintosh Clients Accessing AOLLinux Clients Fixed IP Address Port Options Advanced Port SetupConnection Options Settings Port OptionsTransparent Bridge OptionLoad Balance Load BalanceLoad Balance Settings Load BalanceStatistics InterfaceAdvanced PPPoE Settings Advanced PPPoESelect WAN Port SessionStatus ActionAdvanced Pptp Settings Advanced PptpHost IP Setup Advanced SetupHost Network Identity Settings Host IP SetupBinding Host NetworkHost & Group ListVirtual Servers Connecting to the Virtual ServersVirtual Server Settings Virtual ServerCustom Virtual Servers Settings Custom Virtual ServersSelect Custom Server Server List Name Custom ServerCustom Virtual Server Special Applications Settings Special ApplicationsSelect Special Application Name Special Application Using a Special Application on your PCDynamic DNS To use the Dynamic DNS featureDynamic DNS Service Settings Dynamic DNSWAN Port SettingAdditional Multi DMZ Multi DMZSettings Multi DMZ UPnP Settings UPnPUPnP Option Settings NAT NAT SettingNAT Alias 10 Advanced Feature Advanced FeaturesSession Persistency Protocol, Port Range Settings Advanced Features Interface Smtp Simple Mail Transport Protocol Binding Using Remote Web-based SetupProtocol Protocol and Port Binding Block URL Security ManagementBlock Internet Settings Block URLSetup Access Group Access FilterBlock Well-known Filter SettingPorts Icmp FiltersSession Limit System Filter Exception Planning the VPN VPN ConfigurationIPSec Global Setting IPSec Global SettingLog Level IP Global Setting Global ParametersPolicy Setup Policy SetupIPSec Traffic Binding VPN Policy SetupTraffic Selector Security LevelKey Management Tunnel Attribute IPSec Policy optionsDead Peer Detection Set Options QoS Setup QoS ConfigurationData QoS Setup Policy ConfigurationPolicy Priority Data Policy ConfigurationSnmp Management AssistantEmail Alert Settings SnmpEnable/Disable Settings Email AlertEmail Alert Excessive PingSyslog Sntp Configuration Syslog ConfigurationSyslog Delivery Log Priority ForAdmin Password Screen Admin PasswordUpgrade Firmware Upgrade FirmwareExisting Dhcp Server Advanced LAN ConfigurationRouting Settings Routing Configuring Other Routers on your LANStatic Routing Example For Router Bs Default Route For Router As Default RouteFor the VPN 800/2 Firewall Router Gateways Routing Table Entry 1 SegmentOperation Operation and StatusSystem Status Device Data System StatusRestore Factory Defaults Restore Factory DefaultsWAN Status WAN StatusData NAT Status NAT StatusNAT Traffic ErrorsNAT Connections MiscFCC Statement SpecificationsCE Marking Warning Overview TCP/IP Settings Windows TCP/IP SetupChecking TCP/IP Settings Windows 9x/ME Using Dhcp Select Control Panel Network and Dial-up Connection Checking TCP/IP Settings WindowsUsing a fixed IP Address Use the following IP Address Figure B-7 Network Configuration Windows XP Checking TCP/IP Settings Windows XPFigure B-8 TCP/IP Properties Windows XP General Problems TroubleshootingInternet Access SolutionSolution
Related manuals
Manual 3 pages 12.69 Kb