Datamax DGL STX KF Select Factory Defaults, STX Kf Set Present Distance, STX Kp Module Protection

Page 29

power-up the printer while pressing the PAUSE and CANCEL keys; or, 3) via the printer’s menu system entry System Settings / Set Factory Defaults. (Not supported.)

STX KF - Select Factory Defaults

This command restores the printer’s configuration to the “factory default” settings. These factory default values may be either the Datamax default settings or the configuration file previously specified in the <STX>Kd command. (Not supported.)

STX Kf - Set Present Distance

This command specifies an additional amount to advance the label after printing. (Not supported.)

STX Kp - Module Protection

This command controls memory module protection. When “protected”, a module will ignore format, downloads and delete commands. This command can be useful to add data to Datamax reserved modules, Z (ILPC) and Y (EFIGS). (Not supported.)

STX KQ - Query Memory Configuration

This command causes the printer to transmit its internal DRAM memory configuration to the host device. The transmitted data provides information regarding the total amount of installed internal DRAM, the amount available for configuration and the amount currently assigned to specific functions or entities. (Reported values are not all actual values.)

STX Kq - Query Memory Configuration (new format)

This command causes the printer to transmit its internal DRAM memory configuration to the host device. The transmitted data provides information regarding the total amount of internal DRAM installed, the amount available for configuration, and the amount currently assigned to specific functions or entities. (Not supported.)

STX Kr - Resettable Counter Reset

This command resets the internal counters. Follow this command with an <SOH>U command to retain the reset or the counters will revert to the previous values after cycling power. (Not supported.)

STX KV - Verifier Enable/Disable

This command allows the verifier (option, if installed), to be enabled and disabled. (Not supported.)

STX Kx - Delete Configuration File

This command deletes the specified configuration file. (Not supported.)

29

Image 29

Contents Printer Protocol Interpreter PPI DGL Page Page Copyright 2006 PRINTRONIX, INC Trademark AcknowledgmentsTable of Contents Table of Contents Command Enhancements And Differences STX K- Top of Form, Offset Distance Configuration Setting Compatibility Contact Information Table of Contents Introduction PPI/DGL Setup Menu PPI/DGL Setup MenuCharacter Set PPI/DGL Setup SubmenuActive Euro Character Default ModuleControl Codes Feedback CharsRow Offset Error HandlingColumn Offset Format AttribCommand Ignore Menus Vertical DPI AdjustSoft Switch Length Cmd STXcSTX a Set Time and Date STX a Enable Feedback CharactersSTX B Get Printer Time and Date Information STX c Set Continuous Paper LengthSTX L Enter Label-Formatting Command STX K Extended-System CommandsSTX F Form Feed STX G Print Last Label FormatSTX m Set Printer To Metric STX U Label Format Field ReplacementSTX n Set Printer to Imperial Inches STX o Cycle CutterSTX X Set Default Module STX V Software SettingsSTX y Select Font Symbol Set STX v Print Firmware Version InformationMake Last Field Entered Decrement Numeric Alphanumeric + Make Last Field Entered Increment Numeric AlphanumericSet Count by Amount Set Format AttributeSet Dot Size Width and Height Terminate Label Formatting Mode and Print LabelAdvanced Font Attributes FSn PointsSet Metric Mode Enter Heat SettingSet Inch Mode Imperial Set Print SpeedSelect Font Symbol Set Terminate Label-Formatting ModeSet Slew Rate Store Label Format In ModuleSTX T Print Time and Date STX S Recall Global Data And Place In FieldESC *c###D Assign Font ID Number ESC s###W Font DescriptorChapter SOH *- Reset SOH # ResetSOH C Stop/Cancel SOH a Send Ascii Status StringSTX KC Get Configuration SOH U Update System Database with Current DatabaseSTX Kc Configuration Set STX Kd Set File as Factory DefaultSTX KQ Query Memory Configuration STX KF Select Factory DefaultsSTX Kq Query Memory Configuration new format STX Kr Resettable Counter ResetSTX KD Database Configuration STX Kb Backfeed Time DelaySTX KM Configure Internal Memory Module Size STX KR Reset Memory ConfigurationSTX R Ribbon Saver On/Off STX P Character HEX Dump Mode STX p Controlled PauseSTX T Printhead Dot Pattern Test Label STX t Test RAM Memory ModuleSTX D Memory Dump Test Mode Only STX b Set Cutter signal timeSTX d Set Printer to double buffer mode STX g Internal Batch Software ModeSet Label Backup Speed Select Mirror ModeWait mode Prodigy only Zip Mode Prodigy onlyFonts Internal Bitmapped Non-Proportional fonts DPIISmooth, Scalable and Downloaded fonts Slash ZeroResident Bitmap Fonts CodepagesValid Ascii Characters for bitmap fonts Scalable FontsBarcode Symbologies Plessey UCC/EAN CodePostNet MaxiCodeGraphics Supported graphics objects ImagesFlash / Ram Module compatibility Image FormatsModule Operations Cutter CommandsBi-Directional Communications Command Reference Printer ConfigurationIgnored Commands EmulationsWorkaround Partially Supported Commands Media Settings menu Datamax Setting Description PTX Setting Print Control Menu Datamax Setting Description PTX Setting Printer Options Menu Datamax Setting Description Datamax Setting Description PTX Setting System Settings Menu Datamax Setting Description Pause Mode TRANSPARENT, *XOR Opaque Imaging ModeENABLED, *DISABLED Peel ModeFault Handling Level ENABLED, *DISABLED Menu LanguageHost Settings Host TimeoutDescription PTX Setting Communications Menu Datamax Setting Description PTX SettingDiagnostics Menu Contact Information Appendix B Corporate Offices Corporate OfficesPage 250103-001