Datamax DGL manual STX K- Top of Form, Offset Distance

Page 8

Table of Contents

STX Kx - Delete Configuration File	29
STX Kb - Backfeed Time Delay	30
STX K- - Top of Form, Offset Distance	30
STX KD Database Configuration	30
STX KI - GPIO Input	30
STX KM - Configure Internal Memory Module Size	30
STX KO - GPIO Output	30
STX KR - Reset Memory Configuration	30
STX KS - Configure Scalable Font Cache Size	30
STX KW - Configure Print Width Size	30
STX M - Set Maximum Label Length	30
STX O - Set Start of Print (SOP) Position	30
STX P - Character (HEX) Dump Mode	31
STX p - Controlled Pause	31
STX R - Ribbon Saver On/Off	31
STX T - Printhead Dot Pattern Test Label	31
STX t - Test RAM Memory Module	31
STX w - Test Flash Memory Module	31
STX Y - Output Sensor Values	31
STX Z - Print Internal Information	32
STX z - Pack Module	32
STX b - Set Cutter signal time	32
STX C - Copy Module	32
STX D - Memory Dump (Test Mode Only)	32
STX d - Set Printer to double buffer mode	32
STX g - Internal Batch Software Mode	32
STX N - Enter Internal Batch	32
STX s - Set Printer to single buffer mode	32
e - Recall Printer Configuration	32
f - Set Present Speed	33
M - Select Mirror Mode	33
p - Set Label Backup Speed	33
W - Wait mode (Prodigy only)	33
Z - Zip Mode (Prodigy only)	33
Print Area	33
Fonts	34
Slash Zero	36
Codepages	37
Barcode Symbologies	38
Images	40
Graphics - Supported graphics objects:	40
Flash / Ram Module compatibility	40

Image 8

Contents Printer Protocol Interpreter PPI DGL Page Page Trademark Acknowledgments Copyright 2006 PRINTRONIX, INCTable of Contents Table of Contents Command Enhancements And Differences STX K- Top of Form, Offset Distance Configuration Setting Compatibility Contact Information Table of Contents Introduction PPI/DGL Setup Menu PPI/DGL Setup MenuCharacter Set PPI/DGL Setup SubmenuActive Default Module Euro CharacterControl Codes Feedback CharsError Handling Row OffsetColumn Offset Format AttribVertical DPI Adjust Command Ignore MenusSoft Switch Length Cmd STXcSTX a Enable Feedback Characters STX a Set Time and DateSTX B Get Printer Time and Date Information STX c Set Continuous Paper LengthSTX K Extended-System Commands STX L Enter Label-Formatting CommandSTX F Form Feed STX G Print Last Label FormatSTX U Label Format Field Replacement STX m Set Printer To MetricSTX n Set Printer to Imperial Inches STX o Cycle CutterSTX V Software Settings STX X Set Default ModuleSTX y Select Font Symbol Set STX v Print Firmware Version Information+ Make Last Field Entered Increment Numeric Alphanumeric Make Last Field Entered Decrement Numeric AlphanumericSet Count by Amount Set Format AttributeTerminate Label Formatting Mode and Print Label Set Dot Size Width and HeightAdvanced Font Attributes FSn PointsEnter Heat Setting Set Metric ModeSet Inch Mode Imperial Set Print SpeedTerminate Label-Formatting Mode Select Font Symbol SetSet Slew Rate Store Label Format In ModuleSTX S Recall Global Data And Place In Field STX T Print Time and DateESC *c###D Assign Font ID Number ESC s###W Font DescriptorChapter SOH # Reset SOH *- ResetSOH C Stop/Cancel SOH a Send Ascii Status StringSOH U Update System Database with Current Database STX KC Get ConfigurationSTX Kc Configuration Set STX Kd Set File as Factory DefaultSTX KF Select Factory Defaults STX KQ Query Memory ConfigurationSTX Kq Query Memory Configuration new format STX Kr Resettable Counter ResetSTX Kb Backfeed Time Delay STX KD Database ConfigurationSTX KM Configure Internal Memory Module Size STX KR Reset Memory ConfigurationSTX P Character HEX Dump Mode STX p Controlled Pause STX R Ribbon Saver On/OffSTX T Printhead Dot Pattern Test Label STX t Test RAM Memory ModuleSTX b Set Cutter signal time STX D Memory Dump Test Mode OnlySTX d Set Printer to double buffer mode STX g Internal Batch Software ModeSelect Mirror Mode Set Label Backup SpeedWait mode Prodigy only Zip Mode Prodigy onlyFonts DPI Internal Bitmapped Non-Proportional fontsSlash Zero ISmooth, Scalable and Downloaded fontsCodepages Resident Bitmap FontsValid Ascii Characters for bitmap fonts Scalable FontsBarcode Symbologies UCC/EAN Code PlesseyPostNet MaxiCodeImages Graphics Supported graphics objectsFlash / Ram Module compatibility Image FormatsModule Operations Cutter CommandsBi-Directional Communications Printer Configuration Command ReferenceIgnored Commands EmulationsWorkaround Partially Supported Commands Media Settings menu Datamax Setting Description PTX Setting Print Control Menu Datamax Setting Description PTX Setting Printer Options Menu Datamax Setting Description Datamax Setting Description PTX Setting System Settings Menu Datamax Setting Description TRANSPARENT, *XOR Opaque Imaging Mode Pause ModeENABLED, *DISABLED Peel ModeENABLED, *DISABLED Menu Language Fault Handling LevelHost Settings Host TimeoutDescription PTX Setting Communications Menu Datamax Setting Description PTX SettingDiagnostics Menu Contact Information Corporate Offices Appendix B Corporate OfficesPage 250103-001