Datamax DGL Set Present Speed, Select Mirror Mode, Set Label Backup Speed, Wait mode Prodigy only

Page 33

f - Set Present Speed

(Not supported.)

M - Select Mirror Mode

This command instructs the printer to “mirror” all subsequent print field records. This command toggles the mirroring mode. Mirrored fields are transposed visually, as if the object is viewed in a Printed Result. (Not supported.)

p - Set Label Backup Speed

This command is used for the “Peel and Present” and “Cut Label Operations”. It allows the user to specify the rate at which the printer will reverse the label direction to align the next start of print position. The rate set by this command remains in effect until another backup speed command is received, see Appendix L for valid ranges. The speed is modified via the menu or when the printer is reset. (Not supported.)

W - Wait mode (Prodigy only)

(Obsolete System Command.)

Z - Zip Mode (Prodigy only)

(Obsolete System Command.)

Print Area

When looking at the front of the printer, the origin of the label is positioned at the bottom left of the label, and extends up and to the right. The label length for continuous labels can be set in the Menu and through the <STX>cnnnn command.

On Datamax printers, the print width is adjusted through the menu ‘LABEL WIDTH’. According to the manual, objects extending beyond the page width will not print. However, this does not seem to have any effect on the I-42xx: the full width can always be used. On DGL, objects draw beyond the adjusted page width will not print.

Physical page-rotation is not available on Datamax. When rotation is needed, each object should be rotated individually.

See figure below for a graphical representation of the print area, and the coordinate system used by DGL.

33

Image 33
Contents Printer Protocol Interpreter PPI DGL Page Page Copyright 2006 PRINTRONIX, INC Trademark AcknowledgmentsTable of Contents Table of Contents Command Enhancements And Differences STX K- Top of Form, Offset Distance Configuration Setting Compatibility Contact Information Table of Contents Introduction PPI/DGL Setup Menu PPI/DGL Setup MenuPPI/DGL Setup Submenu ActiveCharacter Set Euro Character Default ModuleControl Codes Feedback CharsRow Offset Error HandlingColumn Offset Format AttribCommand Ignore Menus Vertical DPI AdjustSoft Switch Length Cmd STXcSTX a Set Time and Date STX a Enable Feedback CharactersSTX B Get Printer Time and Date Information STX c Set Continuous Paper LengthSTX L Enter Label-Formatting Command STX K Extended-System CommandsSTX F Form Feed STX G Print Last Label FormatSTX m Set Printer To Metric STX U Label Format Field ReplacementSTX n Set Printer to Imperial Inches STX o Cycle CutterSTX X Set Default Module STX V Software SettingsSTX y Select Font Symbol Set STX v Print Firmware Version InformationMake Last Field Entered Decrement Numeric Alphanumeric + Make Last Field Entered Increment Numeric AlphanumericSet Count by Amount Set Format AttributeSet Dot Size Width and Height Terminate Label Formatting Mode and Print LabelAdvanced Font Attributes FSn PointsSet Metric Mode Enter Heat SettingSet Inch Mode Imperial Set Print SpeedSelect Font Symbol Set Terminate Label-Formatting ModeSet Slew Rate Store Label Format In ModuleSTX T Print Time and Date STX S Recall Global Data And Place In FieldESC *c###D Assign Font ID Number ESC s###W Font DescriptorChapter SOH *- Reset SOH # ResetSOH C Stop/Cancel SOH a Send Ascii Status StringSTX KC Get Configuration SOH U Update System Database with Current DatabaseSTX Kc Configuration Set STX Kd Set File as Factory DefaultSTX KQ Query Memory Configuration STX KF Select Factory DefaultsSTX Kq Query Memory Configuration new format STX Kr Resettable Counter ResetSTX KD Database Configuration STX Kb Backfeed Time DelaySTX KM Configure Internal Memory Module Size STX KR Reset Memory ConfigurationSTX R Ribbon Saver On/Off STX P Character HEX Dump Mode STX p Controlled PauseSTX T Printhead Dot Pattern Test Label STX t Test RAM Memory ModuleSTX D Memory Dump Test Mode Only STX b Set Cutter signal timeSTX d Set Printer to double buffer mode STX g Internal Batch Software ModeSet Label Backup Speed Select Mirror ModeWait mode Prodigy only Zip Mode Prodigy onlyFonts Internal Bitmapped Non-Proportional fonts DPIISmooth, Scalable and Downloaded fonts Slash ZeroResident Bitmap Fonts CodepagesValid Ascii Characters for bitmap fonts Scalable FontsBarcode Symbologies Plessey UCC/EAN CodePostNet MaxiCodeGraphics Supported graphics objects ImagesFlash / Ram Module compatibility Image FormatsCutter Commands Bi-Directional CommunicationsModule Operations Command Reference Printer ConfigurationIgnored Commands EmulationsWorkaround Partially Supported Commands Media Settings menu Datamax Setting Description PTX Setting Print Control Menu Datamax Setting Description PTX Setting Printer Options Menu Datamax Setting Description Datamax Setting Description PTX Setting System Settings Menu Datamax Setting Description Pause Mode TRANSPARENT, *XOR Opaque Imaging ModeENABLED, *DISABLED Peel ModeFault Handling Level ENABLED, *DISABLED Menu LanguageHost Settings Host TimeoutCommunications Menu Datamax Setting Description PTX Setting Diagnostics MenuDescription PTX Setting Contact Information Appendix B Corporate Offices Corporate OfficesPage 250103-001