Datamax DGL Back After Print, ENABLED, *DISABLED Menu Language, Printer Control →, Void Distance

Page 51

Table 4. System Settings Menu

Datamax Setting	Description	PTX Setting

BACK AFTER PRINT	When the present distance is	N/A
	set with the cutter, present
	sensor or GPIO option
	enabled, this setting
	determines the timing of the
	label back up.
	ENABLED, *DISABLED
MENU LANGUAGE	Selects the language in which	PRINTER CONTROL →
	the menu system messages	Display
	and configuration label are	Language
	shown.
FAULT HANDLING LEVEL	When a faulted condition	N/A
*1	(ribbon or paper out, failed
2	bar code, etc.) has been
VOID DISTANCE	detected, this setting
*0.25in (0-2.00)	determines the action to be
RETRY COUNT	taken by the operator and the
*1 (0-3)	printer.

	Table 5. Communications Menu

Datamax Setting	Description	PTX Setting

SERIAL PORT A	Controls the communications	SERIAL PORT
SERIAL PORT B	settings for the Serial Ports.
PARALLEL PORT A	Controls the communications	PARALLEL PORT
PARALLEL PORT B	settings for the Parallel Ports.
NIC ADAPTER	Controls the communications	ETHERNET PORT /
	settings for the Ethernet	ADDRESS / PARAMS
	Ports.
HOST SETTINGS	Settings which affect all
	communications with a host
HOST TIMEOUT	The number of seconds a	All communication port
	communications port must be	menus → Timeout
	idle before the printer may	*10 Sec (1 – 60 Sec)
	process data from a different
	port.
	*10 SEC (1-60)

51

Image 51

Contents Printer Protocol Interpreter PPI DGL Page Page Copyright 2006 PRINTRONIX, INC Trademark AcknowledgmentsTable of Contents Table of Contents Command Enhancements And Differences STX K- Top of Form, Offset Distance Configuration Setting Compatibility Contact Information Table of Contents Introduction PPI/DGL Setup Menu PPI/DGL Setup MenuPPI/DGL Setup Submenu ActiveCharacter Set Feedback Chars Default ModuleEuro Character Control CodesFormat Attrib Error HandlingRow Offset Column OffsetLength Cmd STXc Vertical DPI AdjustCommand Ignore Menus Soft SwitchSTX c Set Continuous Paper Length STX a Enable Feedback CharactersSTX a Set Time and Date STX B Get Printer Time and Date InformationSTX G Print Last Label Format STX K Extended-System CommandsSTX L Enter Label-Formatting Command STX F Form FeedSTX o Cycle Cutter STX U Label Format Field ReplacementSTX m Set Printer To Metric STX n Set Printer to Imperial InchesSTX v Print Firmware Version Information STX V Software SettingsSTX X Set Default Module STX y Select Font Symbol SetSet Format Attribute + Make Last Field Entered Increment Numeric AlphanumericMake Last Field Entered Decrement Numeric Alphanumeric Set Count by AmountFSn Points Terminate Label Formatting Mode and Print LabelSet Dot Size Width and Height Advanced Font AttributesSet Print Speed Enter Heat SettingSet Metric Mode Set Inch Mode ImperialStore Label Format In Module Terminate Label-Formatting ModeSelect Font Symbol Set Set Slew RateESC s###W Font Descriptor STX S Recall Global Data And Place In FieldSTX T Print Time and Date ESC *c###D Assign Font ID NumberChapter SOH a Send Ascii Status String SOH # ResetSOH *- Reset SOH C Stop/CancelSTX Kd Set File as Factory Default SOH U Update System Database with Current DatabaseSTX KC Get Configuration STX Kc Configuration SetSTX Kr Resettable Counter Reset STX KF Select Factory DefaultsSTX KQ Query Memory Configuration STX Kq Query Memory Configuration new formatSTX KR Reset Memory Configuration STX Kb Backfeed Time DelaySTX KD Database Configuration STX KM Configure Internal Memory Module SizeSTX t Test RAM Memory Module STX P Character HEX Dump Mode STX p Controlled PauseSTX R Ribbon Saver On/Off STX T Printhead Dot Pattern Test LabelSTX g Internal Batch Software Mode STX b Set Cutter signal timeSTX D Memory Dump Test Mode Only STX d Set Printer to double buffer modeZip Mode Prodigy only Select Mirror ModeSet Label Backup Speed Wait mode Prodigy onlyFonts Internal Bitmapped Non-Proportional fonts DPIISmooth, Scalable and Downloaded fonts Slash ZeroScalable Fonts CodepagesResident Bitmap Fonts Valid Ascii Characters for bitmap fontsBarcode Symbologies MaxiCode UCC/EAN CodePlessey PostNetImage Formats ImagesGraphics Supported graphics objects Flash / Ram Module compatibilityCutter Commands Bi-Directional CommunicationsModule Operations Emulations Printer ConfigurationCommand Reference Ignored CommandsWorkaround Partially Supported Commands Media Settings menu Datamax Setting Description PTX Setting Print Control Menu Datamax Setting Description PTX Setting Printer Options Menu Datamax Setting Description Datamax Setting Description PTX Setting System Settings Menu Datamax Setting Description Peel Mode TRANSPARENT, *XOR Opaque Imaging ModePause Mode ENABLED, *DISABLEDHost Timeout ENABLED, *DISABLED Menu LanguageFault Handling Level Host SettingsCommunications Menu Datamax Setting Description PTX Setting Diagnostics MenuDescription PTX Setting Contact Information Appendix B Corporate Offices Corporate OfficesPage 250103-001