Datamax DGL manual Format Attributes, Transparent, Xor, TRANSPARENT, XOR Opaque Imaging Mode

Page 50

Appendix A

Table 4. System Settings Menu

Datamax Setting

Description

PTX Setting

FORMAT ATTRIBUTES	Affects the manner in which
	overlapping text and graphics
	are treated as the label is
	printed.
	TRANSPARENT, *XOR,
	OPAQUE

PPI/DGL SETUP → Format

Attrib

TRANSPARENT, *XOR,

OPAQUE

IMAGING MODE	Instructs the printer whether
	to pre-image the label format.
PAUSE MODE	When enabled, suspends
	printing between each label
	until the PAUSE Key is
	pressed.
	ENABLED, *DISABLED
PEEL MODE	Specifies that a Feed
	operation be prevented when
	the label is presented and not
	removed.
	ENABLED, *DISABLED
SECURITY	Provides the user with the
	ability to password protect all
	printer settings made through
	the front panel.
	ENABLED, *DISABLED,
	MODIFY PASSWORD
UNITS OF MEASURE	Selects the measurement
	system in which the system’s
	settings are represented in
	the menu system and on
	configuration labels.
	METRIC, *IMPERIAL

N/A

N/A

MEDIA CONTROL → Media Handling

Tear-off or Peel-off

PRINTER CONTROL → Set Lock Key

PPI/DGL SETUP → Units of

Measure

METRIC, *IMPERIA

INPUT MODE	Defines the type of printer	N/A
	language.
	*DPL, LINE
PLUS EMULATION	Provides compatibility with	N/A
ALLEGRO EMULATION	legacy Datamax emulations.
DPI EMULATION
COLUMN EMULATION
SOP EMULATION

50

Image 50

Contents Printer Protocol Interpreter PPI DGL Page Page Trademark Acknowledgments Copyright 2006 PRINTRONIX, INCTable of Contents Table of Contents Command Enhancements And Differences STX K- Top of Form, Offset Distance Configuration Setting Compatibility Contact Information Table of Contents Introduction PPI/DGL Setup Menu PPI/DGL Setup MenuCharacter Set PPI/DGL Setup SubmenuActive Control Codes Default ModuleEuro Character Feedback CharsColumn Offset Error HandlingRow Offset Format AttribSoft Switch Vertical DPI AdjustCommand Ignore Menus Length Cmd STXcSTX B Get Printer Time and Date Information STX a Enable Feedback CharactersSTX a Set Time and Date STX c Set Continuous Paper LengthSTX F Form Feed STX K Extended-System CommandsSTX L Enter Label-Formatting Command STX G Print Last Label FormatSTX n Set Printer to Imperial Inches STX U Label Format Field ReplacementSTX m Set Printer To Metric STX o Cycle CutterSTX y Select Font Symbol Set STX V Software SettingsSTX X Set Default Module STX v Print Firmware Version InformationSet Count by Amount + Make Last Field Entered Increment Numeric AlphanumericMake Last Field Entered Decrement Numeric Alphanumeric Set Format AttributeAdvanced Font Attributes Terminate Label Formatting Mode and Print LabelSet Dot Size Width and Height FSn PointsSet Inch Mode Imperial Enter Heat SettingSet Metric Mode Set Print SpeedSet Slew Rate Terminate Label-Formatting ModeSelect Font Symbol Set Store Label Format In ModuleESC *c###D Assign Font ID Number STX S Recall Global Data And Place In FieldSTX T Print Time and Date ESC s###W Font DescriptorChapter SOH C Stop/Cancel SOH # ResetSOH *- Reset SOH a Send Ascii Status StringSTX Kc Configuration Set SOH U Update System Database with Current DatabaseSTX KC Get Configuration STX Kd Set File as Factory DefaultSTX Kq Query Memory Configuration new format STX KF Select Factory DefaultsSTX KQ Query Memory Configuration STX Kr Resettable Counter ResetSTX KM Configure Internal Memory Module Size STX Kb Backfeed Time DelaySTX KD Database Configuration STX KR Reset Memory ConfigurationSTX T Printhead Dot Pattern Test Label STX P Character HEX Dump Mode STX p Controlled PauseSTX R Ribbon Saver On/Off STX t Test RAM Memory ModuleSTX d Set Printer to double buffer mode STX b Set Cutter signal timeSTX D Memory Dump Test Mode Only STX g Internal Batch Software ModeWait mode Prodigy only Select Mirror ModeSet Label Backup Speed Zip Mode Prodigy onlyFonts DPI Internal Bitmapped Non-Proportional fontsSlash Zero ISmooth, Scalable and Downloaded fontsValid Ascii Characters for bitmap fonts CodepagesResident Bitmap Fonts Scalable FontsBarcode Symbologies PostNet UCC/EAN CodePlessey MaxiCodeFlash / Ram Module compatibility ImagesGraphics Supported graphics objects Image FormatsModule Operations Cutter CommandsBi-Directional Communications Ignored Commands Printer ConfigurationCommand Reference EmulationsWorkaround Partially Supported Commands Media Settings menu Datamax Setting Description PTX Setting Print Control Menu Datamax Setting Description PTX Setting Printer Options Menu Datamax Setting Description Datamax Setting Description PTX Setting System Settings Menu Datamax Setting Description ENABLED, *DISABLED TRANSPARENT, *XOR Opaque Imaging ModePause Mode Peel ModeHost Settings ENABLED, *DISABLED Menu LanguageFault Handling Level Host TimeoutDescription PTX Setting Communications Menu Datamax Setting Description PTX SettingDiagnostics Menu Contact Information Corporate Offices Appendix B Corporate OfficesPage 250103-001