Datamax DGL manual Euro Character, Control Codes, Feedback Chars, Default Module, Units of Measure

Page 14

Chapter 1 PPI/DGL SETUP Menu

Euro Character

Allows the operator to select the position of the Euro character in the code page.

Control Codes

Allows the operator to change the prefix of the software commands interpreted by the printer.

	S O H	S T X	C R	E S C	‘C o u n t B y ’
S ta n d a rd	0 x 0 1	0 x 0 2	0 x 0 D	0 x 1 B	0 x 5 E
A ltern a te	0 x 5 E	0 x 7 E	0 x 0 D	0 x 1 B	0 x 4 0
A ltern a te 2	0 x 5 E	0 x 7 E	0 x 7 C	0 x 1 B	0 x 4 0
U ser -D efin ed	0 x 0 1	0 x 0 2	0 x 0 D	0 x 1 B	0 x 5 E

When ‘User-Defined’ is selected, 5 additional sub-menus are inserted in the menu tree. These sub-menus allow the user to set a value for each of the control codes. The default ‘User-Defined’ values are shown in the table above.

Feedback Chars

When enabled, the printer returns a Hex 1E [RS] after each label successfully prints, and Hex 1F [US] after each batch of labels is printed.

For invalid characters, the printer responds with Hex 07 [BEL].

•Enabled. Feedback characters are sent to the host.

•Disabled. No feedback characters are sent.

The default is Disabled.

Default Module

Sets the default module used to store files when no module or default module is specified in the command. (See Chapter 3 for further details.)

.

•RAM.

•Flash.

The default is RAM.

Units of Measure

Sets the printer to interpret measurements as Imperial or Metric values.

•Imperial.

•Metric.

The default is Imperial.

NOTE: <STX>n and <STX>m commands override this setting, and stay in effect until the printer is take Offline and back Online.

14

Image 14

Contents Printer Protocol Interpreter PPI DGL Page Page Trademark Acknowledgments Copyright 2006 PRINTRONIX, INCTable of Contents Table of Contents Command Enhancements And Differences STX K- Top of Form, Offset Distance Configuration Setting Compatibility Contact Information Table of Contents Introduction PPI/DGL Setup Menu PPI/DGL Setup MenuCharacter Set PPI/DGL Setup SubmenuActive Control Codes Default ModuleEuro Character Feedback CharsColumn Offset Error HandlingRow Offset Format AttribSoft Switch Vertical DPI AdjustCommand Ignore Menus Length Cmd STXcSTX B Get Printer Time and Date Information STX a Enable Feedback CharactersSTX a Set Time and Date STX c Set Continuous Paper LengthSTX F Form Feed STX K Extended-System CommandsSTX L Enter Label-Formatting Command STX G Print Last Label FormatSTX n Set Printer to Imperial Inches STX U Label Format Field ReplacementSTX m Set Printer To Metric STX o Cycle CutterSTX y Select Font Symbol Set STX V Software SettingsSTX X Set Default Module STX v Print Firmware Version InformationSet Count by Amount + Make Last Field Entered Increment Numeric AlphanumericMake Last Field Entered Decrement Numeric Alphanumeric Set Format AttributeAdvanced Font Attributes Terminate Label Formatting Mode and Print LabelSet Dot Size Width and Height FSn PointsSet Inch Mode Imperial Enter Heat SettingSet Metric Mode Set Print SpeedSet Slew Rate Terminate Label-Formatting ModeSelect Font Symbol Set Store Label Format In ModuleESC *c###D Assign Font ID Number STX S Recall Global Data And Place In FieldSTX T Print Time and Date ESC s###W Font DescriptorChapter SOH C Stop/Cancel SOH # ResetSOH *- Reset SOH a Send Ascii Status StringSTX Kc Configuration Set SOH U Update System Database with Current DatabaseSTX KC Get Configuration STX Kd Set File as Factory DefaultSTX Kq Query Memory Configuration new format STX KF Select Factory DefaultsSTX KQ Query Memory Configuration STX Kr Resettable Counter ResetSTX KM Configure Internal Memory Module Size STX Kb Backfeed Time DelaySTX KD Database Configuration STX KR Reset Memory ConfigurationSTX T Printhead Dot Pattern Test Label STX P Character HEX Dump Mode STX p Controlled PauseSTX R Ribbon Saver On/Off STX t Test RAM Memory ModuleSTX d Set Printer to double buffer mode STX b Set Cutter signal timeSTX D Memory Dump Test Mode Only STX g Internal Batch Software ModeWait mode Prodigy only Select Mirror ModeSet Label Backup Speed Zip Mode Prodigy onlyFonts DPI Internal Bitmapped Non-Proportional fontsSlash Zero ISmooth, Scalable and Downloaded fontsValid Ascii Characters for bitmap fonts CodepagesResident Bitmap Fonts Scalable FontsBarcode Symbologies PostNet UCC/EAN CodePlessey MaxiCodeFlash / Ram Module compatibility ImagesGraphics Supported graphics objects Image FormatsModule Operations Cutter CommandsBi-Directional Communications Ignored Commands Printer ConfigurationCommand Reference EmulationsWorkaround Partially Supported Commands Media Settings menu Datamax Setting Description PTX Setting Print Control Menu Datamax Setting Description PTX Setting Printer Options Menu Datamax Setting Description Datamax Setting Description PTX Setting System Settings Menu Datamax Setting Description ENABLED, *DISABLED TRANSPARENT, *XOR Opaque Imaging ModePause Mode Peel ModeHost Settings ENABLED, *DISABLED Menu LanguageFault Handling Level Host TimeoutDescription PTX Setting Communications Menu Datamax Setting Description PTX SettingDiagnostics Menu Contact Information Corporate Offices Appendix B Corporate OfficesPage 250103-001