Datamax DGL manual Slash Zero, ISmooth, Scalable and Downloaded fonts

Page 36

Chapter 3

ISmooth, Scalable and Downloaded fonts:

Size field

Description

Agfa

(eee)

 

TypeFace

 

Bit-Mapped Resident Fonts

 

A04 – A72(1)

CG Triumvirate, Bit-Mapped Smooth Font

 

000 - 010(1)

(Point sizes 4, 5, 6, 8, 10, 12, 14, 18, 24, 30,

 

 

36, 48 and 72)

 

 

Scalable Resident Fonts (standard)

 

S00

CG Triumvirate Bold Condensed

 

 

S01

CG Triumvirate

 

 

 

Scalable Resident Fonts (optional)

 

 

SA0

CG Times

 

 

SA1

CG Times Italic

 

 

SA2

CG Times Bold

 

 

SA3

CG Times Bold Italic

 

 

U40

Gothic B Kanji, Double Byte (Binary)

 

 

u40

Gothic B Kanji, Double Byte (Hex ASCII)

 

 

UC0

GB Simplified Chinese, Double Byte (Binary)

 

 

uC0

GB Simplified Chinese, Double Byte (Hex

 

 

 

ASCII)

 

 

UH0

Korean Hangul, Double Byte (Binary)

 

 

uH0

Korean Hangul, Double Byte (Hex ASCII)

 

 

 

Bit-Mapped Downloaded Fonts

 

 

100 - 999

Bit-Mapped Downloaded Fonts

 

N/A

 

Scalable Downloaded Fonts

 

 

S50 - S5z...

Single Byte (Binary)

 

N/A

S90 - S9z

 

 

 

U50 -U5z...

Double Byte (Binary)

 

N/A

U90 -U9z

 

 

 

u50 -u5z...

Double Byte (Hex ASCII)

 

N/A

u90 -u9z

 

 

 

Font ID 9 uses the Size field (eee) in the Record Format to select the Smooth, Scalable, or Downloaded fonts.

NOTE: For I42xx: The Smooth Internal CG Triumvirate Bitmap Fonts are automatically converted to the CG Triumvirate Scalable Font, which therefore also affects the code pages.

Slash Zero

All resident bitmap fonts use the slashed zero by default. This can be disabled through Label Formatting command ‘z’.

None of the scalable fonts have the slashed zero available.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents
Printer Protocol Interpreter PPI DGL Page Page Trademark Acknowledgments Copyright 2006 PRINTRONIX, INCTable of Contents Table of Contents Command Enhancements And Differences STX K- Top of Form, Offset Distance Configuration Setting Compatibility Contact Information Table of Contents Introduction PPI/DGL Setup Menu PPI/DGL Setup MenuPPI/DGL Setup Submenu ActiveCharacter Set Default Module Euro CharacterControl Codes Feedback CharsError Handling Row OffsetColumn Offset Format AttribVertical DPI Adjust Command Ignore MenusSoft Switch Length Cmd STXcSTX a Enable Feedback Characters STX a Set Time and DateSTX B Get Printer Time and Date Information STX c Set Continuous Paper LengthSTX K Extended-System Commands STX L Enter Label-Formatting CommandSTX F Form Feed STX G Print Last Label FormatSTX U Label Format Field Replacement STX m Set Printer To MetricSTX n Set Printer to Imperial Inches STX o Cycle CutterSTX V Software Settings STX X Set Default ModuleSTX y Select Font Symbol Set STX v Print Firmware Version Information+ Make Last Field Entered Increment Numeric Alphanumeric Make Last Field Entered Decrement Numeric AlphanumericSet Count by Amount Set Format AttributeTerminate Label Formatting Mode and Print Label Set Dot Size Width and HeightAdvanced Font Attributes FSn PointsEnter Heat Setting Set Metric ModeSet Inch Mode Imperial Set Print SpeedTerminate Label-Formatting Mode Select Font Symbol SetSet Slew Rate Store Label Format In ModuleSTX S Recall Global Data And Place In Field STX T Print Time and DateESC *c###D Assign Font ID Number ESC s###W Font DescriptorChapter SOH # Reset SOH *- ResetSOH C Stop/Cancel SOH a Send Ascii Status StringSOH U Update System Database with Current Database STX KC Get ConfigurationSTX Kc Configuration Set STX Kd Set File as Factory DefaultSTX KF Select Factory Defaults STX KQ Query Memory ConfigurationSTX Kq Query Memory Configuration new format STX Kr Resettable Counter ResetSTX Kb Backfeed Time Delay STX KD Database ConfigurationSTX KM Configure Internal Memory Module Size STX KR Reset Memory ConfigurationSTX P Character HEX Dump Mode STX p Controlled Pause STX R Ribbon Saver On/OffSTX T Printhead Dot Pattern Test Label STX t Test RAM Memory ModuleSTX b Set Cutter signal time STX D Memory Dump Test Mode OnlySTX d Set Printer to double buffer mode STX g Internal Batch Software ModeSelect Mirror Mode Set Label Backup SpeedWait mode Prodigy only Zip Mode Prodigy onlyFonts DPI Internal Bitmapped Non-Proportional fontsSlash Zero ISmooth, Scalable and Downloaded fontsCodepages Resident Bitmap FontsValid Ascii Characters for bitmap fonts Scalable FontsBarcode Symbologies UCC/EAN Code PlesseyPostNet MaxiCodeImages Graphics Supported graphics objectsFlash / Ram Module compatibility Image FormatsCutter Commands Bi-Directional CommunicationsModule Operations Printer Configuration Command ReferenceIgnored Commands EmulationsWorkaround Partially Supported Commands Media Settings menu Datamax Setting Description PTX Setting Print Control Menu Datamax Setting Description PTX Setting Printer Options Menu Datamax Setting Description Datamax Setting Description PTX Setting System Settings Menu Datamax Setting Description TRANSPARENT, *XOR Opaque Imaging Mode Pause ModeENABLED, *DISABLED Peel ModeENABLED, *DISABLED Menu Language Fault Handling LevelHost Settings Host TimeoutCommunications Menu Datamax Setting Description PTX Setting Diagnostics MenuDescription PTX Setting Contact Information Corporate Offices Appendix B Corporate OfficesPage 250103-001