Cobalt Networks manual Setting Up 9084 Network Remote Control, Rear I/O Module Installation

Page 24

2		Setting Up 9084 Network Remote Control

Align and engage mounting tab on Rear

1 I/O Module with the module seating slot on rear of frame chassis.

DSCN3483A.JPG

Hold top of Rear I/O Module flush against

2 frame chassis and start the captive screw. Lightly tighten captive screw.

DSCN3487A.JPG

Figure 2-2 Rear I/O Module Installation

Setting Up 9084 Network Remote Control

Perform remote control setup in accordance with Cobalt® reference guide “COMPASS™ Remote Control User Guide” (PN 9000RCS-RM).

Note: • If network remote control is to be used for the frame and the frame has not yet been set up for remote control, Cobalt® reference guide COMPASS™ Remote Control User Guide (PN 9000RCS-RM)provides thorough infor- mation and step-by-step instructions for setting up network remote control of COMPASS™ cards using DashBoard™ . (Cobalt® OGCP-9000 and OGCP-9000/CC Remote Control Panel product manuals have complete instructions for setting up remote control using a Remote Control Panel.)

Download a copy of this guide by clicking on the Support>Downloads link at www.cobaltdigital.com and then select DashBoard Remote Control Setup Guide as a download, or contact Cobalt® as listed in Contact Cobalt Digital Inc. (p. 1-15).

•If installing a card in a frame already equipped for, and connected to DashBoard™ , no network setup is required for the card. The card will be dis- covered by DashBoard™ and be ready for use.

2-4

9084 PRODUCT MANUAL

9084-OM (V4.0)

Image 24

Contents 9084 Cobalt Digital IncCopyright DisclaimerTrademark Information Table of Contents Operating Instructions Introduction OverviewCard Software Versions and this Manual SupportDownloads link atManual Conventions E201Safety Summary Labeling Symbol DefinitionsFunctional Description Input/OutputsProcessor VideoColor Corrector Color Corrector Video ProcessorFrame Sync Function AFD InserterComputer with NIC DashBoard Remote Control User Control InterfaceCard Edge Controls Controller CardOther cards installed in openGear frames such as the Cobalt Rear I/O Modules Video Formats Supported byRaster Structure Frame Rate Technical Specifications CharacteristicTechnical Specifications Introduction Warranty and Service Information Cobalt Digital Inc. Limited WarrantyContact Cobalt Digital Inc PhoneFax Web General Information Technical SupportThis page intentionally blank Installation and Setup Installing the 9084 Into a Frame SlotInstalling the 9084 Into a Frame Slot Installation and Setup Installing a Rear I/O ModuleSetting Up 9084 Network Remote Control Rear I/O Module InstallationOperating Instructions Control and Display DescriptionsFunction Submenu/Parameter Submenu Overview Submenu a Submenu b Submenu z Individual ParametersCard Edge Controls, Indicators, and Display FunctionCard Edge Control Menu/Submenu Structure Menu Depth LEDsNone Card Edge Setup Abbreviated Diagram VidSubmenu Depth ClrCS p DashBoard User Interface Set Enable to On Channel Black AdjCorrection Cobalt Remote Control Panel User Interfaces Control Panel Setup of Example Video Proc FunctionAccessing the 9084 Card via Remote Control Accessing the 9084 Card Using DashBoardAccessing the 9084 Card Using a Cobalt Remote Control Panel Checking Card Using Info Card Edge Controls Power Consumption and Temperature DisplaysChecking 9084 Card Information Software Version NumberDefault Line No. / Range Ancillary Data Line Number Locations and RangesFormat Line No. Limiting FormatFunction Submenu List and Descriptions Function Submenu ItemReset to Unity Video ProcLuma Gain Luma LiftColor Phase Color GainGang Luma and Color Gain Black Hard ClipApplies white hard clip limiting at specified percentage 50.0% to 109.1% null = 109.1%Card Edge Control Menu Applies white soft clip limiting at specified percentageOutput Mode Incoming AFDOutput Code Output LineOperating Instructions Black Adj. Green Red BlueGang Black Level Controls White Adj. Green Red BlueGang Gamma Controls Framesync Enable Vertical Delay ControlHorizontal Delay Control Video Delay Display Loss of Input Signal SelectionMinimum Latency Frames Control Framesync Status DisplayReset Framesync Framesync LOS Freeze ColorCustom Color Hue Custom Color SaturationPreset Name field and Preset Save button Preset Load button and the Selected PresetPreset Save and Load Selected Preset drop-down listReset Current Preset Function Parameter/Setting Video ProcPreset Name Download PresetsColor and Video Correction Examples Using Feed To SwitcherOn-Set Monitor Color Correction Example Anchor Desk Set with Monitor10 Uncorrected Uncompensated Monitor Waveform To Switcher From Monitor Video Feed 12 Applying Correction to Example Monitor Waveform Signal Condition Observed On Waveform Monitor Correction Using Miscellaneous Color and Video Correction ExamplesLuma gain less than 100% level as shown below for VAR10.PNG VAR10A.PNG Troubleshooting Error and Failure Indicator OverviewCard Edge Status/Error Indicators and Display Status/Error Input Format Indicators IndicatorsCharacter Alphanumeric Display AlphanumericDashBoard Status/Error Indicators and Displays Indicator Icon or Display Error Description15 Selecting Specific Cards for Card Info Status Display Basic Troubleshooting Checks ChecksProcessing Error Troubleshooting Symptom Error/Condition Corrective ActionTroubleshooting Network/Remote Control Errors Case of ProblemsPage 2406 E. University Ave. Urbana, IL 9084-OM