Cobalt Networks 9084 manual DashBoard User Interface

Page 31

Operating Instructions

Control and Display Descriptions

The timeout period from when a menu is entered to when the display times outs (reverts to the default card model display) can be adjusted from 5 to 9999 seconds (166.7 minutes) as described below.

1.Access the Displ (Display) menu.

2.Use the up/down switch to enter the desired timeout value as shown below.

Card Edge Control Menu:

Disp

1

 

2

 

TOUT

 

 

 

 

 

(value)

Timeout value (in seconds)

 

 

 

 

DashBoard™ User Interface

(See Figure 3-5.) The 9084 function submenus are organized in DashBoard™ using tabs (for example, “Color Correction” in Figure 3-5). When a tab is selected, each parametric control or selection list item associated with the function is displayed. Scalar (numeric) parametric values can then be adjusted as desired using the GUI slider controls. Items in a list can then be selected using GUI drop-down lists. (In this manner, the setting effected using controls and selection lists displayed in DashBoard™ are comparable to the submenu items accessed and committed using the 9084 card edge controls.)

Figure 3-5shows the same setup described in Figure 3-3as performed using DashBoard™ . Note how this setup is greatly simplified using DashBoard™ with most of the discrete tasks ( A through I in Figure 3-3) performed with the card edge controls now rolled into simple actions using DashBoard™ .

9084-OM (V4.0)

9084 PRODUCT MANUAL

3-7

Image 31
Contents Cobalt Digital Inc 9084Disclaimer CopyrightTrademark Information Table of Contents Operating Instructions Overview IntroductionSupportDownloads link at Card Software Versions and this ManualE201 Manual ConventionsLabeling Symbol Definitions Safety SummaryInput/Outputs Functional DescriptionVideo ProcessorColor Corrector AFD Inserter Color CorrectorVideo Processor Frame Sync FunctionController Card Computer with NIC DashBoard Remote ControlUser Control Interface Card Edge ControlsOther cards installed in openGear frames such as the Cobalt Video Formats Supported by Rear I/O ModulesRaster Structure Frame Rate Characteristic Technical SpecificationsTechnical Specifications Introduction Cobalt Digital Inc. Limited Warranty Warranty and Service InformationWeb General Information Technical Support Contact Cobalt Digital IncPhone FaxThis page intentionally blank Installing the 9084 Into a Frame Slot Installation and SetupInstalling the 9084 Into a Frame Slot Installing a Rear I/O Module Installation and SetupRear I/O Module Installation Setting Up 9084 Network Remote ControlControl and Display Descriptions Operating InstructionsSubmenu a Submenu b Submenu z Individual Parameters Function Submenu/Parameter Submenu OverviewFunction Card Edge Controls, Indicators, and DisplayMenu Depth LEDs Card Edge Control Menu/Submenu StructureNone ClrC Card Edge Setup Abbreviated DiagramVid Submenu DepthS p DashBoard User Interface Channel Black Adj Set Enable to OnCorrection Control Panel Setup of Example Video Proc Function Cobalt Remote Control Panel User InterfacesAccessing the 9084 Card Using DashBoard Accessing the 9084 Card via Remote ControlAccessing the 9084 Card Using a Cobalt Remote Control Panel Software Version Number Checking Card Using Info Card Edge ControlsPower Consumption and Temperature Displays Checking 9084 Card InformationLine No. Limiting Format Default Line No. / RangeAncillary Data Line Number Locations and Ranges FormatFunction Submenu Item Function Submenu List and DescriptionsLuma Lift Reset to UnityVideo Proc Luma GainBlack Hard Clip Color PhaseColor Gain Gang Luma and Color GainApplies white soft clip limiting at specified percentage Applies white hard clip limiting at specified percentage50.0% to 109.1% null = 109.1% Card Edge Control MenuOutput Line Output ModeIncoming AFD Output CodeBlack Adj. Green Red Blue Operating InstructionsWhite Adj. Green Red Blue Gang Black Level ControlsGang Gamma Controls Vertical Delay Control Framesync EnableHorizontal Delay Control Framesync Status Display Video Delay DisplayLoss of Input Signal Selection Minimum Latency Frames ControlCustom Color Saturation Reset FramesyncFramesync LOS Freeze Color Custom Color HueSelected Preset drop-down list Preset Name field and Preset Save buttonPreset Load button and the Selected Preset Preset Save and LoadDownload Presets Reset Current PresetFunction Parameter/Setting Video Proc Preset NameAnchor Desk Set with Monitor Color and Video Correction Examples UsingFeed To Switcher On-Set Monitor Color Correction Example10 Uncorrected Uncompensated Monitor Waveform To Switcher From Monitor Video Feed 12 Applying Correction to Example Monitor Waveform Signal Miscellaneous Color and Video Correction Examples Condition Observed On Waveform Monitor Correction UsingLuma gain less than 100% level as shown below for VAR10.PNG VAR10A.PNG Error and Failure Indicator Overview TroubleshootingAlphanumeric Card Edge Status/Error Indicators and DisplayStatus/Error Input Format Indicators Indicators Character Alphanumeric DisplayIndicator Icon or Display Error Description DashBoard Status/Error Indicators and Displays15 Selecting Specific Cards for Card Info Status Display Checks Basic Troubleshooting ChecksSymptom Error/Condition Corrective Action Processing Error TroubleshootingCase of Problems Troubleshooting Network/Remote Control ErrorsPage 2406 E. University Ave. Urbana, IL 9084-OM