Cobalt Networks 9084 manual Introduction

Page 17

Introduction

Technical Specifications

 

 

 

Table 1-2 Technical Specifications — continued

 

 

 

Item

Characteristic

 

 

 

 

Pre-Processor (Reclocked) Serial Digital

Return Loss:

 

Video Outputs (cont.)

> 15 dB at 5 MHz – 270 MHz

 

 

 

 

> 12 dB at 270 MHz – 1.485 GHz

 

 

Signal Level:

 

 

800 mV ± 10%

 

 

DC Offset:

 

 

0 V ± 50 mV

 

 

Jitter (HD):

 

 

< 0.15 UI (all outputs)

 

 

Jitter (SD):

 

 

< 0.10 UI (all outputs)

 

 

Overshoot:

 

 

< 0.2% of amplitude

 

 

 

 

Reference Video Input

Number of Inputs:

 

 

Two Non-Terminating (looping) Frame Reference Inputs

 

 

Standards Supported (HD):

 

 

720p 24; 25; 29.97; 30; 50; 59.94

 

 

1080i 25; 29.97

 

 

1080p 23.98; 24; 25; 29.97; 30

 

 

1080psF 23.98; 24

 

 

Standards Supported (SD):

 

 

486i 29.97 (NTSC)

 

 

575i 25 (PAL)

 

 

Signal Level:

 

 

1 Vp-p nominal

 

 

Signal Type:

 

 

Analog video sync (black burst or tri-level)

 

 

Impedance:

 

 

75 Ω

 

 

Return Loss:

 

 

> 30 dB to 30 MHz

 

 

Allowable Maximum DC on Ref Input:

 

 

±1.0 V

 

 

 

 

9084-OM (V4.0)

9084 PRODUCT MANUAL

1-13

Image 17
Contents Cobalt Digital Inc 9084Trademark Information CopyrightDisclaimer Table of Contents Operating Instructions Overview IntroductionSupportDownloads link at Card Software Versions and this ManualE201 Manual ConventionsLabeling Symbol Definitions Safety SummaryInput/Outputs Functional DescriptionColor Corrector ProcessorVideo Video Processor Color CorrectorFrame Sync Function AFD InserterUser Control Interface Computer with NIC DashBoard Remote ControlCard Edge Controls Controller CardOther cards installed in openGear frames such as the Cobalt Raster Structure Frame Rate Rear I/O ModulesVideo Formats Supported by Characteristic Technical SpecificationsTechnical Specifications Introduction Cobalt Digital Inc. Limited Warranty Warranty and Service InformationPhone Contact Cobalt Digital IncFax Web General Information Technical SupportThis page intentionally blank Installing the 9084 Into a Frame Slot Installation and SetupInstalling the 9084 Into a Frame Slot Installing a Rear I/O Module Installation and SetupRear I/O Module Installation Setting Up 9084 Network Remote ControlControl and Display Descriptions Operating InstructionsSubmenu a Submenu b Submenu z Individual Parameters Function Submenu/Parameter Submenu OverviewFunction Card Edge Controls, Indicators, and DisplayNone Card Edge Control Menu/Submenu StructureMenu Depth LEDs Vid Card Edge Setup Abbreviated DiagramSubmenu Depth ClrCS p DashBoard User Interface Correction Set Enable to OnChannel Black Adj Control Panel Setup of Example Video Proc Function Cobalt Remote Control Panel User InterfacesAccessing the 9084 Card Using DashBoard Accessing the 9084 Card via Remote ControlAccessing the 9084 Card Using a Cobalt Remote Control Panel Power Consumption and Temperature Displays Checking Card Using Info Card Edge ControlsChecking 9084 Card Information Software Version NumberAncillary Data Line Number Locations and Ranges Default Line No. / RangeFormat Line No. Limiting FormatFunction Submenu Item Function Submenu List and DescriptionsVideo Proc Reset to UnityLuma Gain Luma LiftColor Gain Color PhaseGang Luma and Color Gain Black Hard Clip50.0% to 109.1% null = 109.1% Applies white hard clip limiting at specified percentageCard Edge Control Menu Applies white soft clip limiting at specified percentageIncoming AFD Output ModeOutput Code Output LineBlack Adj. Green Red Blue Operating InstructionsWhite Adj. Green Red Blue Gang Black Level ControlsGang Gamma Controls Horizontal Delay Control Framesync EnableVertical Delay Control Loss of Input Signal Selection Video Delay DisplayMinimum Latency Frames Control Framesync Status DisplayFramesync LOS Freeze Color Reset FramesyncCustom Color Hue Custom Color SaturationPreset Load button and the Selected Preset Preset Name field and Preset Save buttonPreset Save and Load Selected Preset drop-down listFunction Parameter/Setting Video Proc Reset Current PresetPreset Name Download PresetsFeed To Switcher Color and Video Correction Examples UsingOn-Set Monitor Color Correction Example Anchor Desk Set with Monitor10 Uncorrected Uncompensated Monitor Waveform To Switcher From Monitor Video Feed 12 Applying Correction to Example Monitor Waveform Signal Miscellaneous Color and Video Correction Examples Condition Observed On Waveform Monitor Correction UsingLuma gain less than 100% level as shown below for VAR10.PNG VAR10A.PNG Error and Failure Indicator Overview TroubleshootingStatus/Error Input Format Indicators Indicators Card Edge Status/Error Indicators and DisplayCharacter Alphanumeric Display AlphanumericIndicator Icon or Display Error Description DashBoard Status/Error Indicators and Displays15 Selecting Specific Cards for Card Info Status Display Checks Basic Troubleshooting ChecksSymptom Error/Condition Corrective Action Processing Error TroubleshootingCase of Problems Troubleshooting Network/Remote Control ErrorsPage 2406 E. University Ave. Urbana, IL 9084-OM