Citizen Systems CBM-270 user manual Operation, Connecting AC Adapter

Page 21

CBM-270 User’s Manual

Feeds the paper. It is fed continuously while the switch is held down. For the label paper, it is fed by

one label.

(6)Paper holder

Set the paper roll in this holder.

(7)PNE sensor

Detects that the paper is running out.

(8)DIP switch

Initially sets the printer at power-on and sets the functions.

(9)Label detection sensor (L and M spec. only)

Detects the labels. Deals with either the label interval or black mark.

(10)Platen roller unit

Detach this unit when the paper is jamming or when you clean the head.

(11)Head-up lever

Used when replacing the paper or detaching/reattaching the platen roller unit.

(12)Paper cutter

Cuts the printed paper.

(13)Power connector

Connects to the accessory AC adapter (27AD).

(14)Interface connector

Connects to a communication interface cable. There are two types, for serial and parallel interfaces.

(15)Printer cover

Detach this cover when replacing the paper.

4.OPERATION

4.1Connecting AC Adapter

1.Turn off the power.

2.Connect the cable connector of the AC adapter to the power connector located on the back of the printer.

3.Connect the AC power cord of the AC adapter, and plug it into a socket.

CAUTION:

1)Use only the specified AC adapter.

2)When disconnecting/reconnecting the cable connector of the AC adapter, be sure to hold the connector.

3)Separate the AC adapter from other noise-generating devices.

4)Pulling the AC power cord may damage it, resulting in a fire, electric shock, or snapping.

5)If a thunder/lightning storm is nearby, disconnect the AC adapter from the socket and do not use the printer, because a fire or electric shock may occur.

6)Do not put the AC power cord close to a heating device. Its coating can melt and cause a fire or electric shock.

7)Install the printer in a well-ventilated place, because the AC adapter generates heat when it is used.

8)Use the specified AC power source. Connect to a power source with sufficient capacity. If the capacity is

Image 21

Contents Citizen EMC LVDWichtige Sicherheitsanweisungen Lärmemission kleiner 70dBA Sicherheitshinweis CBM-270 User’s Manual Safety Precautions Be Sure to Observe CBM-270 User’s Manual Precautions for Installation Precautions for Handling Daily Maintenance Contents Appendix German113 Features Basic SpecificationsOutline UnpackingBasic Specifications EMI Paper Specifications Recommended PaperPrinting Position Head and Paper Cutter Layout Outer Appearance and Component Parts Operation Connecting AC AdapterCBM-270 User’s Manual Connecting Interface Cable Inserting the Paper How to Remove Remaining Paper Roll Eliminating the Paper Jam When Thermal Paper is Used Feed Switch FunctionWhen Label Paper is Used When the Macro is ExecutedOFF Paper Near End FunctionSelf-Print Function Auto-Loading FunctionError Details Operation Panel and Display of Error12 Red/Black Print Precautions for Use OFFCBM-270 User’s Manual Location of DIP Switch DIP Switch SettingDIP Switch Function Jumper Wire FunctionUSA Specifications Connectors Pin ConfigurationParallel Interface Input and Output Signals Input and Output SignalsElectrical Characteristics Timing Chart Buffering Data Receiving ControlRXD Serial InterfaceDTR DSRData Configuration Output TXD, DTR Printer Side Host Side Error DetectionPower Connector Maintenance and Service Print Control Functions Command ListDescriptions of Each Item Command DetailsXxxx Command Details CBM-270 User’s Manual ESC SP n ESC ! n ESC % n ESC & s n m a p s×a m−n+1 ESC * m n1 n2 d k Print Results Dots single density Dots double density ESC 3 n ESC − nESC = n ESC E n ESC D n k NULESC G n ESC J nESC !, ESC G See Sample Program and Print Results for ESC 2 on ESC R n ESC V n Default Sample ProgramESC a n ESC c 4 n ESC c 3 n Parallel Interface OnlyESC d n ESC c 5 nESC t n ESC n nFixed to Not defined Sample Program ESC Serial Interface OnlyESC n ESC $ n1 n2 ESC \ n1 n2 UPC-A UPC-E JAN13 EAN JAN 8 EAN Code GS k n d k NULCodabar NW-7 UPC-ACODE39 JAN-8EANITF CodabarCode Btestcode A123 TestUPC-E GS h n GS w nDefault See Also GS f Sample Program Print Results GS f n GS / m GS * n1 n2 d n1 × n2 ×Vertical Direction Horizontal Direction Normal mode CBM-270 User’s Manual GS n1 n2 n3 Only When Label Printer is Selected DC2 a nDC3 n GS FF, GS GS FFGS C0 m n GS C1 n1 n2 n3 n4 n5 n6 GS C N1 N2 N3 N4 N5 GS C2 n1 n2GS c Character Codes Table GS a m n Only When Label Printer is SelectedInternational Domestic International Character Codes Table Appendix 1. Block Diagram Appendix 2. Outline Drawing Appendix 3. Wall Mounting Holes Layout Drawing Vorsicht GermanPage Warnung Vorsicht ZU Beachtende SicherheitsmassregelnWarnung Vorsichtsmassregeln FÜR DIE Aufstellung Vorsichtsmassregeln FÜR DIE Handhabung Vorsicht Tägliche WartungAnschließen des Netzteils BetriebAnschließen des Schnittstellenkabels Einsetzen des Papiers Entnehmen der eingesetzten Papierrolle Beseitigen von Papierstau Papierende-Funktion FEED-SchalterfunktionBei Verwendung von Thermalpapier Bei Verwendung von EtikettenpapierPapiermangel-Funktion Busy DTR/FAULT PaperSelbstdruckfunktion AutoladefunktionBedienfeld und Fehleranzeigen Fehler-Einzelheiten 12 Rot/Schwarz-Druck VorsichtsmaßregelnVorsicht Lage der DIP-Schalter DIP-SCHALTEREINSTELLUNGDIP-Schalterfunktion Jumperdraht-FunktionItalien Japan Wartung UND Dienst